We have an ASA 5508 running 7.0.4 FTD code and managed by FDM. I used this guide to configure Duo:https://networkwizkid.com/2021/12/16/configuring-duo-two-factor-authentication-2fa-for-cisco-remote-access-vpns-ra-vpn-using-the-firepower-device-manage...
We're looking at buying a Cisco 2130 NGFW. The plan is to connect using the SFP+ on the firewall to SFP+ on a Dell N3224T-ON, is there any reason not to use one of the uplink ports on a switch to connect these two devices together? We're wanting to g...
Good morning or afternoon, everyone.I have an ASA 5545-X that is reloading constantly and with a 'no boot image' to load from. I reset it to factory defaults and reloaded/restarted it, that was yesterday morning. I have put it into 0x41 & 0X1 and tri...
Hello community, as rumors go, EOS for the ASA 5506 is within reach. If you belong to the group using ASA 5506 with Firepower Services, this will kinda feel like the end of life as we know it. At least to anyone firewalling the bejesus out of the ASA...
Hi, After a power outage and issues with the UPS, we see an issue with failover. The first thing I noticed when login in to the CLI of the secondary firewall, was this message - "You have logged in while system startup is in progress. Please wait, ...
Hi,I have an ASA 5520 on FW 9.0(4).I have on it 3 subnets : inside (10.1.1.0/24)outside (1.1.1.2/28, webserver Public ip 1.1.1.3)DMZ (20.1.1.0, webserver DMZ ip 20.1.1.10)Clients on the inside are able to access internet without any issueWebserver lo...
I have a number of Cisco ASA devices that i want to upgrade the ASA/ASDM software on.The all run in active / standby mode.I have a mixture of ASA5525-X, ASA5545-X and ASA5555-X devices.They all run:Current ASA version = 9.8(4)10Current ASDM = 7.13(1)...
a web site we use is using HTTP. when it reaches its destination its redirected to HTTPS. Cisco FTD IPS policy is blocking the redirect. how do we enable this through IPS?
Please guide me for changing TLS version on Cisco sf300 sw version 1.4.2.4
Hi All, I'm in the middle of integrating log sources into LogPoint, where FMC is one of them.Logpoint has FMC on their list of integrations, but I'm not able to finde any documentation? I'm a bit reluctant to setup syslog in every policy and so forth...
Hi, I am a beginer for Cisco Anyconnect, and I'd like to know about compatibility. I found the compatibility of Windows OS, MacOS, Linux, and Anyconnect at the address below. https://www.cisco.com/c/en/us/td/docs/security/vpn_client/anyconnect/anycon...
Hello, we scan a switch with Qualys for vulnerability and found some issue as below. Anyone can tell what it does mean and provide some suggestion to fix it? Thank you "OpenSSH is a set of computer programs providing encrypted communication sessions...
Hi community, I'm looking for some guidance... We're relatively new to FTD devices and in the progress of upgrading from legacy ASA 5008x's that were managed independently. We have deployed an FMCv and are managing a new HA instance consisting of 2 x...
For an ASA 5510 on 6.3(3), how do I get: terminal pager 24 To stick? Somehow on one of our older ASA's no matter what I do, it always pager disabled so it just scrolls without stopping. I need it to stop ever 24 lines or 50 lines or whatever I set ...
Hello I know this question is questioned a lot, but i need help to understand the steps and configuration. FMC ----> FTD-HQ -----> WAN ------> FTD-RemoteI need to understand the procedure.1--> FMC_REAL_IP ----> FMC_NAT2--> i need to configure mgmt in...
