seeing a lot (thousands) hits of this signature with the victim as a printer or sms device. Is this something I need to be concerned about?
seeing a lot (thousands) hits of this signature with the victim as a printer or sms device. Is this something I need to be concerned about?
Hi,I want to configure port security on a switch into which a failover PIX pair are configured. However, fromhttp://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/12_1e/swconfig/port_sec.htmit appears that this may not be possible due to the PI...
Hi,We've been trying to get our new Cisco IDS 4235 sensor + VMS Basic to work for the last few days but with no success:1) Install CiscoWorks VMS Common Services 2.2 with SP2 with the supplied vms 2.2 startup disk2) Install IDS MC 1.2.3 from the star...
Hi all,I want to use a RADIUS server (Microsoft IAS) to handle group and user authentication for my Easy VPN Server (a 3845).I've read this:http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122t/122t8/ftunity.pdf...which detail...
Where can I find information on version 7 of the pix software?I have noticed that there are books on amazon advertising version 7.
I have a requirement of providing Internet access to INSIDE users based on groups using a PIX firewall with multiple Zones connecting to 3 Internet uplinks ( different modes like 1 Leased Line, 1 ADSL & 1 ISDN ) as shown in the enclosed slide. Can so...
Which interface is interface 0? Ethernet0? This is my outside interface. Why would my outside interface being communicating with the other pix, when I have a dedicated failover interface with x-over cable?Jan 12 02:06:26 lab-pix515e-pix1.com Jan 12...
Hi All,Have a main office (192.168.x.x, Cisco 1721, IOS 12.3) and a branch office (10.250.1.x, Linksys AG041), both connected to the web via ADSL.Have setup a tunnel between the Cisco 1721 and the Linksys AG041 (I am based in UK if model is unfamilia...
I have some material coming, but I would like just to see if this works. I have a Cisco 2621 router with a VPN module. I have set if up as best as I currently can, but still, I cant make a connection. What am I missing?Config:aaa new-modelaaa authori...
What am I doing wrong?I am connected directly to the cisco 1700 and can access the www but when I type https://10.10.10.1 as directed inthe manual I get page cannot be displayed. HELP!!!
What is the purpose of running OSPF on PIX ,as PIX will not do any routing.I guess it will just allow PIX to learn routes from neighbors and routes will be useful for PIX itself.Am I correct ?
Hi all,I need an help to set the correct timeout on a Cisco PIX, in fact after a connection and disconnection between two videoconferencing devices, sometimes the TCP connection rest in idle and I cannot connect again. If I clear the xlate (clear the...
I was curious as to where other administrators have their IDS devices on their network. Do you have the span set up to monitor a trunk link off a main closet? The reason I'm asking is that I notice the memory utilization on our local device is cons...
I have 10 exiesting PIXs. I'm scared about Firewall MC. It wants to convert my NAT 0 acls to the below.Why can't it just work with what it imported? What change the ACL names, etc?NAT Conversionaccess-list acl_mdc_inside_access deny ip any any log ...
I would like to redirect my port 80 traffic from my inside interface to the dmz interface.I have a pix 515e and three interfaces - inside (private net), outside (pub net Internet) and dmz1 (which has a squid proxy)What I want is when a user makes a w...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-25-2025 04:32 PM | ||
06-25-2025 04:40 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM | ||
06-11-2025 07:59 AM |
User | Count |
---|---|
4 | |
3 | |
2 | |
1 | |
1 |