I have setup up a number of FTDS that are managed by FMC in CML labs. I have setup the in-built desktop in CML that is hanging off a FTD. I am able to get the internet via FTD-->Router (NAT)-->External Connector and I am able to get internet access f...
Forum Posts
Hi AllI am currently looking into ddos protection services to protect some main internet links.What options are out there? I assume it would need to be further up the chain i.e in the ISP / Cloud ? Also, I see lots of them use BGP flowspec, what trig...
We have two Cisco FMC-4600v7.2.9 (build 44) running in HA is two separate geographical sites. Both were in HA and running perfectly. HA failover also working perfectly. But now it's showing HA Sync Failed. Please find the screenshots shown below.Plea...
Hi everyone, I passed the exam today, but the report shows only percentages, not the actual marks. I would like to know the minimum percentage required to pass the exam. Best Regards, Ye Htut
HelloBeen struggling with a Cisco 1120 today, no warranty left, but would like to get it running again. Tried a new disk and flashed it with tftp from rommon, also tried USB. Unit comes up with FXOS, but not able to install FTD with scope --> firmwar...
Hello,I have a question about if the FTD license is Out of Compliance status,what is the potential impact on the license regarding the security updates?Does it take the updates or do I have to fix the situation to sync the updates?Thank you.
Hello, If we want to use WCCP on a FTD firewall to redirect web traffic to a Palo Alto Web Proxy, is that possible? I know that Palo Alto doesn't support WCCP but since it would be a Cisco device doing the re-direction, does the receiving device nee...
Resolved! FTD over Remote FMC - 2 FMC Setup
Hi All, I'm in bit of a pickle here as I have a task at hand that has 2 FMC's and 2 FTD's present: Below is the scenario; In an existing setup that constitutes of a FMC(VM) and local FTD's deployed in HA, lets call them FMC-A and FTD-1) are in produ...
hi Cisco experts, can someone teach me how to use FMC API to get all the members of a given network group object? and how to create an network group object and add all the members using API.
Resolved! Talos Connectivity Problem
Hi to all ,i am getting many messages as the following:Severity: criticalModule: Talos CommunicationDescription: 3 modules failed:* URLDB- Failed to retrieve beaker inventory* LSP- Failed to retrieve beaker inventoryMy subscription is active (it expi...
Resolved! TCP-state-bypass on FMC managed FTD
Hi All,I'm seeing tons of %FTD-4-419002: Duplicate TCP SYN from Inside:x.x.x.x/36769 to OUTSIDE:y.y.y.y/80 with different initial sequence number on multiple FTDs where the source IP x.x.x.x is ThousandEyes Enterprise agents' IPs.I've found this doc ...
I have lately realised that there is no way to actually figure out the physical interfaces used by a port-channel in FTD 4110s or 2120s or probably any FTDs through the FMC gui or FTD cli. I asked TAC about this and they also advise there is no way t...
as cisco firepower 2130 throughput is 10 Gbps raw and 5.4 Gbps NGFW and ISP and 760 Mbps when TLS decryption is enabled . Is this 760 Mbps is the overall throughput of the firewall when TLS decryption is enabled or non TLS traffic can pass through 5....
I have 2 x FTD2110 managed by an FMCv, all v6.2.2. I'm trying to create an HA pair using an EtherChannel rather than a single physical link. However, only the physical interfaces are appearing in the dialog box to create the HA pair. The documentatio...
Hello Experts,We have a Cisco Firepower 2130 in production running version 7.4.2.4 which we manage via FMC. A Port-Channel with a VLAN has been configured on the FTD with its own IP address serving as the gateway for DHCP clients while the FTD serves...
