Ask Me Anything Event Thank you for joining us for the Expert Insights Series on ACI & NDI: Empowering Data Center Excellence! Our Customer Success Specialists Cody Albea, Peter Nalley and Manuel Valasco will be available from May 15, 2025 throug...
Forum Posts
Hi All, The ucsmsdk python package provides a code-gen feature which automatically generates python code when we do some activity over UCS manager. I have tried it over a UCS emulator. But when i tried the same with the actual hardware, it failed...
Hello, Could someone help me determine if OTV is supported on the Nexus 3K line of switches, specifically the 31108TC-V? I do not see the 3K line in the Cisco featureset navigator. Thanks a lot for your help! *Update* Heard back from my Cisco rep OTV...
Hi We are trying to migrate N7000 (F2) to N7700 (F3). While copying configuration and reloading N77 we see following error ....Tcam will be over used, please enable bank chaining and/or turn off atomic update.If bank-chaining is enabled on other mo...
I am trying to install ESXi 6.5 on a C240M5L server but in the process of installation it does not detect the virtual disk, I have 6 hard drives in RAID 5
Hello Hans, Seeking for support from you, I've got a scenario where I need to choose breakout 40g-4x10g cable between Nexus 31108TC-V and Catalayst 3850Stack. I've some doubts regarding this. Below is topology detail Doubts 1. If I use breakout...
Hi Team, Need suggestion to migrate Data Center. We have a plan to move eg Heathrow Data Center to Swindon. There are many Services hosted in Heathrow like DHCP Services, Juniper Remote access VPN services. Apart from that, there are many applicati...
Hi Team, We have a plan to migrate one of our DC in Heathrow to Swindon. We do not have much information about application dependanies, so we are planning to keep IP addressing in Target DC for Servers, VMs. Could you please confirm if we can use C...
there is one SM Fibre of 20 Km distance and which I want to connect on N5K-C5548UP model of switch , can any suggest which model of SFP should I use to connect this Single mode Fibre to my N5K switch . IOS of N5K switch is version 6.0(2)N2(1).
Hello Experts, I turn my head towards you again seeking inputs to resolve an issue in bringing up a SVI on Nexus 5010 that I want to use for Peer-keepalive. I have similar config on both 5010's. However, SVI on switch is up and not on other. F...
We use cisco dcnm to find out on which port / interface a server is connected to a FEX or the Nexus switches (9332PQ and 9372PX-E). Unfortunately, the DCNM does not display this information (Cisco Prime does if the device is connected to a Nexus 93...
i have cisco switch model no IE4000-16GT4G-E. i preparing datasheet for that i couldn't found some specifications from online. i need yur help.i what to know following specifications. 1.switch latency period 2.IGMP group 3.Forwarding bandwith 4.Forwa...
This topic is a chance to discuss more about the changes that the Data Center technology has gone through in order to meet business requirements and to learn more about the best practices and troubleshooting tips on Nexus. The session focus in all ...
Hi, I have issue with N2K-C2348UPQ4F, First time we connected to N7K with 7.3.(2)D1(1) for 2 weeks, after that we disconnect from N7K and connect to N5K-C5648Q with 7.1(4)N1(1) but N2K does't came up , Can you advise what should we do ? Below...
In previous vPC setups with N5k (or also N6k), I had to use the 'vpc bind-vrf' command to ensure the forwarding of multicast over the vpc peer-link, especially for receivers in in non-vPC VLANs and the receivers connected to Layer 3 interfaces.I am w...
Hi all, We need replace to a pair of switches with new ones without interrupting traffic. In order to do that , for some minutes all 4 switches will be interconnected between them - but we need to avoid stp recalculations - has anybody done that? any...
