Hi all, I have bumped into a strange issue and on a C1116-4P router running IOS XE Fuji 16.9.1. While ip http secure-server was configured and working, after a router reload it never went up. Show ip http server status command always shows the ...
Hi all, I have bumped into a strange issue and on a C1116-4P router running IOS XE Fuji 16.9.1. While ip http secure-server was configured and working, after a router reload it never went up. Show ip http server status command always shows the ...
Hi, So I'm configuring a new FTD box to replace a legacy ASA 5510 (that still feels strange...calling ASA5510's "legacy" - but I guess I'm showing my age). Anyway, the plan is to set up the FTD box in a side by side config on a spare IP in our pu...
Hi guys. My client replaced an ISR1941 with an ISR4331. On the 1941, there is an ipsec tunnel which works fine but doesn't come up on the 4331. The configurations are identical. Any ideas?
Hello, I am no expert so my apologies if this question comes across as silly. Please see the attached topology, it is a centralized model in which "Remote site A" and "Remote site B" connect to "HQ" via L2 extensions, and then connect to one anoth...
I'm having trouble with configuring a Cisco WS-C3560V2-24PS-S. Traffic is being tagged with an unexpected VLAN id. I have the following VLAN config on the Switch: interface Vlan1 no ip address shutdown ! interface Vlan110 ip address 192.168.1...
Hi all!, I'm a beginner on Cisco systems, in fact I'm being learning about CCNA for the last weeks in order to get the certification in a few months. The reason for this post is related to issues that I have been experiencing with a Cisco Router 36...
Hello, I want to make sure that the special RJ45 connectors that I am considering will fit side-by-side on a Cisco switch. What is the physical distance between ports on Cisco switches, or this switch in particular?
please help me . i have done my ccna & am planning to do my ccda. i dont know how to start & what to refer to or how to practise . help!
Hello all, I have a hopefully quick question. I have recently begun to use the Cisco 4351 ISR in our networking setup. I am looking for a method or process to test the ASync break out cables from the NIM module to the DB-25. Our current process ...
hello dears i have 2960 switch and its suddenly stops booting and its reload continuously .so I tried to load new IOS using xmodem , but the same problem remains. i tried 5 different versions but all the same (i have download the images from cisco ...
Hello, I need to block ingress ntp and snmp traffic from the Internet to a few IP blocks our company owns and live inside our network. The ACL needs to be created on an ASR1001. Here's the ACL I created but I am not 100% sure if it is correct. Do y...
Hello Expert, can someone please explain me How to TRUNK Between CISCO 2960 and 3com 5500g ? But I am not able make this work. Thanks for your Help
Hello, we are trying to stream some video between two Crestron-Devices, one transmitter (10.43.1.66) and one receiver (10.43.1.90). I configured multicast routing via Pim sparse mode with a rendezvous point. After about 2 minutes the stream stops. If...
Hi All, I have two identical catalyst 3750 switches, one is in production, the other is brand new. Both have the same software versions installed on them. I copied the running-config off of the switch that is live on our network and saved it onto a...
Hi, It's possible to create a backplane stack between two SG-550x (one 24T and the other 24F) and three SG-250x (48T) switchs? I need both management and LAG working on the stack... it's possible? Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM |