Other Network Architecture Subjects

Hello all,I have a question re the setup below.I have two routers peering eBGP with an external AS 350 and iBGP between the routers which (just for info) are separate locations.Now if I receive a route (say 168.1.0.0) that has a metric inbound on bot...

Problem is that I have a 7206 that I am trying to connect to a 2500 using a back-to-back configuration. My 7206 has a X21 Octal Cable, which I assumed to be DTE, as other connections are plugged into BT WAN provider. My obvious thought would be to ...

Hican i backup FR subinterface with X25 subinterface with the command backup interface ?it work with X25 interface but with X25 subinterface the router don't accept the command, i don't know if it's a bug or this feature not exist.thanks

I have a cat5500 with the rsm blade, (rsp2) using version 12.2(17a)and have started having this problem. The router will freeze, and then reload a portion of the code, but traffic stops while this is happening, I reload the full switch and it stops ...

I am getting strange ip address sequence in my 3640 router log messages. Does anyone know what this ip address 13.13.13.13 has beeing used for?Iam getting strange message in my 3640 router with strange ip address 13.13.13.13Do you know any informatio...

I have 2 questions about CMS.1. I have just put in a 2950-12 switch at a remote location that is connected to my office via a 256K frame relay circuit. The CMS is very slow to open the web console i can telnet into the switch with no problem. How do ...

I uploaded the image in the Cisco 1700 from c1700-y-mz.122-4.YA2.bin to c1700-y-mz.122-4.YA6.bin. But I started getting the error "Serial0/0 is up, line protocol is down" on the router 2600 which has a serial link to the 1700 on which we did the upgr...

Estoy haciendo el CCNA, y me surgio una duda:Resulta que el hub me divide el ancho de banda de acuerdo a los hosts que esten conectados al hub..Y el switch me crea un circuito virtual, es decir no particiona el ancho de banda....Hasta ahi todo bien.....

We have 1720 box that have One wic card with two serial inerface on that. Problem >>> when i connect v35 cable to s0 interface. link dosent workbut when i connect the same cable to s1 it workes fine, Once wic interface card has been replaced.version ...

Hi,My router doesnt support NBAR, can someone tell me how can I do a traffic pattern study on the router, I want to do a TOP N analysis for protocols serviced by serial link on 2600 series router with IOS 12.1.1.Thanks and RegardsSalim

I recently heard through a friend that there is a way to connect your routers aux port to a switch's con port as a back door of sorts if you can't connect to the switch through telnet and you are not on site. Can anyone tell me how to setup my router...

About this vulnerability:http://www.cisco.com/warp/public/707/NTP-pub.shtmlIn the document above say that for the train 12.2 is neccesary load the 12.2(10) (maintenance release).And I have two routers, 7206 running 12.2(12f)7206 running 12.2(17a)Is n...

I'm running CW2000 RME 3.5 on solaris and confused about the archived config files not being updated. When searching the latest archived configs by pattern "looking for exec-timeout 0 0" its finding this pattern in the running archived configs when ...

Hi,We have a private p2p DS-3 between 2 facilities, used for monitoring and management of a remote facility. For 6 hours each day a database is copied across this line that puts it at about 85% utilization for most of that duration, the rest of the ...

Hi: I just meet a problem that seems very strange.I config HSRP on two router as follow: R1:interface FastEthernet0/0.10 encapsulation dot1Q 120 ip address 26.176.63.91 255.255.255.0 no ip redirects standby 120 ip 26.176.63.98 standby 120 timers 10...