After installing Cisco Works 2000, 5th. Edition, on a new Win2k Pro workstation, when I try to access parts of the Resource Manager, I am getting "Internal Server Error". I have applied all of the Win2K patches and the Cisco Works Patches.
After installing Cisco Works 2000, 5th. Edition, on a new Win2k Pro workstation, when I try to access parts of the Resource Manager, I am getting "Internal Server Error". I have applied all of the Win2K patches and the Cisco Works Patches.
Hi!I have kind of an easy question however i haven't find enough info about it. In the output of show interfaces what "throttles" exactly means. At the moment i'm troubleshooting a FastEthernet interface and i'm having aprox. 1 throttle every 5 minut...
Can you install CiscoWorks and QoS Policy Manager on the same box?
Hey,I have:- a doble star with 2 Cisco 3550 with FX100.- STP is "ON" with UDLD is on each port needed, message interval 15 (agressive mode).- Each 2950 uplink is connected to both 2950, STP is "ON" and UDLD on requiered port too (agressive mode).- Fi...
Good Morning all,what is the maximum possible lenght of the copper to run GigaEthernet on RJ45.I remember around 100 mt (as FE), but I did not find any cisco web site link to confirm this.Any help is appreciated.ThanksMatteo
HiI've set up individual L3 ports on a 3550 which act as router ports for various sites connected via SHDS (LES circuits).Do I need to specify ip helper addresses on each of these individual ports or can I just put them on the L3 gig port which conne...
We have BVIs with the corresponding subinterfaces.There is no possibility to configure CGMP on a BVI. How to handleIGMP Requests on the L3 Interface of the router (BVI)?
HiAm I missing something here? I have imported a couple of images for a 2950 switch into the Image Library and can successfully browse them, however when I go to Image Distribution and select the 2950 that I want to upgrade the Recommended Image page...
we have a NAS setup comprising of AS5300 and PRI links grouped into a hunting group. Currently all the dialin users are V.90 modem users using PSTN to log into the NAS after getting authenticated by the AAA server. Now we have requirement to add ISDN...
This is the weirdest thing I have seen in awhile. I just purchased 3 2924XLs, new in box. But each switch does not have a base mac address(set to all zeros)Is this possibly a diagnostic mode?I would appreciate any help.Jonathan Nantel
Hi,I can see on serial interface of router-"Received 58 broadcasts, 0 runts, 0 giants, 0 throttles"What may be the cause of broadcast received on serial interface( point to point link)...its very strange for methanks
Presently I am using LIghtnings Multicom Access 4 routers for my private network which is connected either by ISDN or by 2Mbps leased line which spans over 30 WAN locations. Now I am interested to expand my network using Cisco Routers. Is there any o...
accidently I've loaded the wrong firmware image to a Catalyst 2924 and booted it. The original file name was c2900XL-c3h2s-mz-120.5-xu.binBecause of the needed memory space, I've deleted the wrong image. But now it is not possible to reload a new fil...
Hello,I have a Cat6503 and want to check the imageversion for the msfc2 card, but find any output commands.I'm not sure if Sup2Vis works fine, because there is no 'slot info' for msfc2.Thanks for helpRuedish vers and sh modul output below.-----------...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |