Other Network Architecture Subjects

I am experiencing a problem starting the EssentialsDbEngine. I am running LMS 2.1 on Win2k 5.0 sp2. When I look at the win2k Event Viewer for Applications I see an error message for the EssentialsDbEngine with the following description: "Cannot op...

We have 2 SUP1A blades with MSFC. In order to place the sup's into a redundant configuration do I need to upgrade the MSFC cards to MSFC2's or will two MFSC's work?

How much delay should I expect when using traffic shaping on a Frame Relay connection, FIFO queuing?This is a 3640, IP only, 12.2(5a) 32MB dram. The router is not busy.The connection is a simple serial connection, 1,280Kbps to a DCE device, Cisco IAD...

Hi %SYS-4-P2_WARN: 1/Invalid crc, dropped packet, count = 1496 Can anyone help me out.Thanks in advanceregards,

I am trying to place an IP address on the management interface of a supervisor engine on a 4507 switch running native IOS, with very little success.I should be grateful if someone out there could advise me how I get into the management interface. Pl...

I recently installed LMS2.1 with Cisco View - the devices come up correctly (cat 4006 IOS and cat 6513 IOS) but I cannot configure any of the ports - example to add a name to a specific port - an error appears. This does not happen on the existing C...

Feb 3 16:34:38: %SEC-6-IPACCESSLOGP: list 120 permitted udp 10.10.1.5(631) -> 10.10.1.255(631), 1 packetWhat kind of packet is 631?

What information does a router need to route a packet?

We get emails from DFM but nothing in the DFM monitoring console. Does the errors clear automatically even if the check box to clear is not checked. I seem to remember that the mesages stayed up until you cleared them. We did a network test plan fail...

I'm trying to configure the following using a Cisco2651 at remote site with multiple BRI interfaces and a Cisco 3640 with PRI at the core.Remote:I have 1 x Server dual attached to two ethernets A (contains user workstations) & B 1x 2651 with e0/0 on ...

Hi I have 4 6500 switches.Tried executing immediate execution command in batch reports.Got the output for 3 switches and last one gave the output " internal error"Gave the correct telnet and enable password in admin-inventory-change attributes. But s...

We are using CWLMS v2.0 and want to know if this product can be used in the following set-up:i) CWLMS will be installed on a server that will have 2 NIC cards- one NIC will be used for serving Administrator Access and the other one will be used for g...

Hi,There is a Fast-Ethernet fiber-multimode-trunk between a Cat6509 and a Cat5000. It worked perfectly for years. Now there are messages on the Cat5000:2003 Feb 03 08:09:07 MET +01:00 %DTP-5-NONTRUNKPORTON:Port 1/2 has become non-trunk2003 Feb 03 08:...

Hello,We are using two Cat4006 as central switches and Cat2950 switches on floors in our company. Floor switches connected to central switches over gbic modules. Our internal network is operating on 4 VLANs configured on each switch.We have serious n...

I ran debug all and I can't understand the information:Jan 30 10:14:06: IP: s=10.10.32.13 (Ethernet0/1), d=10.10.32.255 (Ethernet0/1), len 137, rcvd 3Jan 30 10:14:06: UDP: rcvd src=10.10.32.13(631), dst=10.10.32.255(631), length=117Jan 30 10:14:06: I...