FASTBOOT is invoked by setting configuration register bit 4; What exactly is does thsi do ie. what is FASTBOOT?
FASTBOOT is invoked by setting configuration register bit 4; What exactly is does thsi do ie. what is FASTBOOT?
I have a network with the following config. Site A and site B connected via VPN tunnels thru pix. Access-list says don't nat site A to site B and permit site A to site B thu the vpn tunnel. (and vice versa) Off site A there is a stub network (sit...
Hi,in my network are two Distribution Switches - same Hardware, Software and Configuration Scheme.If I send an IP Options Ping "ping -r 9 xx.x.x.x" to or. from SW-1 or. an access switch behind him, everything works fine.If I send the same ping to SW-...
Hello everyone!I want to use route map to route only ftp traffic over ADSL link. All other traffic must go over leased line.Sample config:interface FastEthernet0 ip address 1.1.1.1 255.255.255.0 ip nat inside ip policy route-map ADSL-trafficaccess-li...
Hi everyone. I am trying to make some tests performance on Ubr 7246VXR ( at the moment it has only DOCSIS 1.0) and the relative HFC network. I would like to analyse how many upstream channels I can combine together per upstream port and 2) analyse ho...
hellocan i configure an AS5350 to let the radius server give IP adresses to remote dialing users.traditionally radius is used to authenticate users , but i hope it can not only authenticate but also dispatch IP adresses to remote users.i have the rad...
hello can i configure an AS5350 to let the radius server give IP adresses to remote dialing users. traditionally radius is used to authenticate users , but i hope it can not only authenticate but also dispatch IP adresses to remote users. i have the ...
I am replacing a Nortel AN at one of our remote sites with a new Cisco 2611XM. This unit utilizes an ISDN BRI for backup purposes.Does anyone have experience with a Cisco to Nortel ISDN PPP connection?I have no idea where to start, so any help would ...
Presently I am running with the following switches3512 XL Enterprises edition (2 gbic modules)3524 XL Enterprises edition (2 gbic modules)3548 XL Enterprises edition (2 gbic modules)Since the production of the above switches has been stopped. Please...
I have a Panasonic PBX with 8 port ISDN card and a 2611XM with NM-8B-S/T. Can I connect them together? How? I have the above equipments in another location and two 2611XM can see each other on IP network. I want to interconnect two PBX.
Have a problem with sm_server hoggin CPU on a windows box. Need to stop DFM from starting when LMS starts up but need to know the startup file to edit. Also, any suggestions on what could be causing sm_server to be using so much CPU?? Cannot Monitori...
I have used 2.3 for quite some time and received this error sporadically but since I have upgraded to CDOne 5, I get it more frequently. I have not upgraded IPM 2.4 due to the Release Notes advising against it running on the same server. Even thoug...
Hi, can the PCMCIA flash memory cards that come with the RSPs be use from a PC? In the label of the card, it says i can insert it in my computer, so, can i format, copying images from my PC to the flash card? thanks ahead for your comments.
I have several devices connected to a wire, let's say 210.20.0.0/25. There's RIP configured among them, that way:!router rip version 2 redistribute connected redistribute static network 210.20.0.0 no auto-summary!One of the devices, 210.20.0.1, has a...
Hello I have a question about the implementation of RSTP on catalyst 2950, so is it possible to take advantage of RSTP without using MSTP ? Like it seems to be possible on catalyst 6K in version 7.5.thanks in adavanceOlivier
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
01-22-2025 07:00 AM | ||
12-30-2024 06:12 PM | ||
11-14-2024 09:33 AM | ||
10-24-2024 11:51 PM | ||
10-20-2024 10:52 PM |