The quick start guide came with the package says to use RJ-49, but Cisco Interface Cards Installation Guide says RJ-48C to RJ-48C BRI Cable. what exactly to use? i am a newbie, your help will be greatly appreciated.yi
I want to send debugging output to the syslog server. I already have the commands Logging history warningsLogging facility local4Is the command I need to add-- logging history debuggingAlso I couldn't find any reason to use the history command. Wh...
I currently have a router that is an LP state. I am not showing the serial interface being in loopback (loopback not set) when I do a show interface cmd. Is there something I need to do to clear it out of an LP state? Jeff
I am using IOS 12.1(1)T on a 1603R and can't seem to set ip dscp values under my policy-map setdscp..... the IOS doesn't recognise SET as a command.Is it the IOS version , do I need to update ?
Hello !!Can i change the default UDP-port 80 for Http Requests over a proxy-server when i use the following config:HTTP RAW operation through a Proxy ServerIn this example http://www.proxy.cisco.com is the proxy server and http://www.xyz.com is the H...
Hello,I have not found a solution regarding callback to Windows 98 and W2000. I have tested with Cisco 3640 with both 11.3 and 12.1 IOS. My error-messages is provided from a debug below. Is my problem related to bug CSCdj81013?Aug 13 15:52:08.149: Mo...
Hello Im not convinced with the following 'sh ip mroute ' output. The Flags CJT are missing eventhough there are directly connected members s . But evrythng seems to be working fine. Also what is 6d14h/stopped, Thanksldn-lw4-r106# sh ip mroute IP Mu...
I am trying to set 'ip next-hop' to a non-connected ip address but it doesn't work I expected it. I remember reading somewhere that it will do a routing lookup for the non-connected address. Is it related a specific code version? Any advise??Thanks,...
Hi,we have a frame-relay connection with LLQ applied to it foroutbound traffic and we want to apply the same policy forinbound traffic as well but when we try this we get theerror: CBWFQ : Can be enabled as an output feature onlyany ideas?the exist...
I configured a 3524 XL with static unicast mac addresses on different port (same address on different ports) for a stonegate application (Firewalls Cluster). I wanted to evoluate to 3550-12G, but it doesn't seem to work anymore. Does anyone know if s...
Sep 11, 2002, 11:53pm PST use Switch Catalyst 2924 Xl as Command Switch and Cat 2912 as member switch. Some of my iMac and G3 are hookup to the Cat 2924Xl and work very well, I can see the my IPShare Server and the other computer on the network but ...
I am trying to upgrade from hybrid to native. I have a MSCF2 module, In ROMMON mode i have formatted the bootflash because i had the wrong IOS, I then installed a c6sup bin file. The file uncompressed and when rebooted in hangs atStart as Primary pro...
I recently had some problems upgrading from my Cat6500 CatOS 6.2(3) to CatOS 6.3(8). Just wondering if anyone else has had any problems like I experienced. My success rate is 75% so far. Scenario 1:Successfully TFTP’ed 6.3(8) to slot0: of active (mo...
I notice Output drops on serial interface which is configured for Frame-relay. WFQ is being used on the interface. I have disabled IP Fast Switching on the interface, but that does not seem to solve the problem. There are no Input Errors or CRC error...
If you wanted to do an audit of Cisco equipment, how do you find out the serial number of say a 1600 router or a 1000 series router - without physically looking at the router. I know that you can find the serial number of a WIC installed in a 1600 se...
