Other Network Architecture Subjects

I have a DMZ outlook web access server that allows all my users with the static ip addresses of 172.16.5.0 network translated on the PIX to have direct internet connection. However my WAN users 172.17.0.0 network on certain segments that are allowe...

I have a 2620 w 12.15YB 16MB Flash/64MB RAM. We're migrating from ISDN to DSL. I can connect with both interfaces to their respective ISP. Desired result is to listen on the BRI dialer for incoming requests and for internal traffic to go out of the D...

After upgrading to CD1 4th edition and RME 3.3 on Solaris 2.6 get the following error message when doing /etc/init.d/dmgtd stop.Error: connect to dmgtd process on "127.0.0.1" on port 42340 failed.Also get this error message when running pdshow! Yet C...

We are employing sampled netflow on GSR16 running eBGP peer with other AS and FIFO queue,and i set sampling interval as 1000. Now GSR16 exports the records to NFC ASDetailMatrix configured, but found flows always record only 1 packet,seldom 2 or 3 pa...

Hi,I am trying to configure an AS5400 IOS 12.2 to limit the number of sessions of the users, I mean, I am interested in 1 user - 1 session .Could anyone help me?,thanks!

I've got a router where I change the default gateway, but when I do a traceroute the connection still goes through the old gateway. Is there a command I'm missing that tells the router to use the new one?

Hi, I've got 3 3500 switches in a GigaStack loop configuration.(3 cables)Now I've bought 2 new 3548s.Can I disconnect the redundant loop safely, add the GigaStack cables for the new switches and configure them using the web Cluster Management interfa...

Hello!!!Can anybody tell me what the following output means??Serial0/1:1 is reset, line protocol is down-I do understand that "Serial0/1" means slot0/port1, but what does :1 mean? as well as the rest of the output. Thank you in advance for your coope...

The Nortel router that connects one of our subnets reports that all of our switches are sending ICMP Type 8 packets to it every 1 second. The ICMP source address is the address of each of the switches and the destination is the router. A 'Sniff' of...

I have a 2621 that I would like to upgrade the IOS on. I would like to go to a 12.1 release and am unsure of what version to choose. If anyone has any suggestions or additional information please let me know ThanksPreston

I have a HP 4050N that is shared via a NT 4.0 sp6a server. I've recently moved the server into a different vlan than the 4050. Since doing that I lose communication with the 4050 on a regular basis. I have to re-create the port on the server for it t...

I would like to set up a switch to act like two smaller switches. Each of the smaller switches containing seperate networks. Is it possible to set up VLANs by network ID? Or should I just seperate half the ports for one vlan and half for the other...

If someone could download the most recent IOS with just IP for the 1601 R Router I would greatly appreciate it!! I only have guest access for now and can't get it myself. You can e-mail it to itech@rsolutions1.com Thank you!!!!

Hello,I hope, that anybody can help me.So, there are three components, which works together but with unwanted side effects.From Cisco - two Catalyst 4006 (with WS-X4232-L3).From Microsoft - Windows 2000 Advanced server with Network Load Balancing (ak...

Hi, I am not sure if it is possible to do but certainly worth a try. I want to write an unix script that will go at specified time and grab the config from the cisco device and save it back to the unix box. Now couple of other issues that needs to ad...