Hi, I am trying to configure an extended named ACL for this Router in packet-trace for an assignment and nothing I do seems to work. I am trying to get just one network to have access to FTP. The current commands I have are: ip access-list extended W...
Forum Posts
I upgradedthe image on 3850-48P, transfer and installation of the image was successful. After reload command I see BOOT_FAIL screen and and I am unable to go to ROMmon mode either. I have attached the console image.Any help?Thanks and regards
aku baru saja memebeli switch baru,ketika aku mencoba login via serial di putty, hanya ada pesan %Error opening tftp://255.255.255.255/network-confg (Timed out) *mar 1 xx:xx:xx %sys-4-CONFIG_RESOLVE_FAILURE : System config parse from ( tftp://255.255...
We have this network upgrade plan and would greatly appreciate your valuable input.Our current network setup consists of the following switches, all connected via 1GB Fiber links:- Cisco C3560G as the Core Switch- 10 Cisco C2960X Access SwitchesWe've...
We're planning to upgrade our network, and we'd love to have your input.Management has changed their mind with phases upgrade.Currently, our network includes a Core Switch (Cisco C3560G) and 10 Access Switches (Cisco C2960X), all connected through 1G...
Hello mates, I have a situation where the customer has two VLANs running on the same physical interface, and we need to implement a shared rate limit -lets say 1 Gbps- for both VLANs. This will ensure that the combined traffic from both VLANs does no...
Resolved! Cat6500 IOS: how to power-up a linecard
Hi,I am managing a couple of Cat 6506 IOS.I can reset or shutdown a linecard (e.g. a NAM) using the "hw-module" command; does exist any command to power up a shutted down line card?Best regards.Paolo Calcaterra
I am recieving this frequent warning alerts "Te12/9 Receive Power Sensor on SW-NL-EDC_eupdswcore001 ".switch is 6513swcore001#sh inventoryNAME: "Transceiver Te12/9", DESCR: "X2 Transceiver 10Gbase-SR Te12/9"Can you please what all issues related to a...
We are working with a customer that is moving from MPLS to SD-WAN solution for all 20 or so of their locations. We have a POC active currently with the SD-WAN handoff on a layer3 interface vlan assigned to a trunk port on a Catalyst 3850 switch. We...
In the following topology... we have five routers where AS 234 is the service provider. There’s one customer with two sites, AS 1 and AS 5. Our customer wants to exchange 1.1.1.1 /32 and 5.5.5.5 /32 between its sites using BGP. To achieve this, we’ll...
On web interface appear the following message: FATAL ERROR: ALLOWED MEMORY SIZE OF ------------ BYTES EXHAUSTED
I'm trying to figure out how to remove a single line from anaccess list when in config mode. I keep reading all this stuffabout using the no form of the access-list command butthat removes the entire access list. Any help is appreciated.
I'm helping a group at work, who just got a 10gig internet connection. I have tons of experience with everything except QSFP cables etc etc. this is what I'm trying to do:10gig Internet-----------> Cisco 8300 ---------40G QSFP ----------> Cisco Nexus...
Hi everyone,i'm once again asking for help in my GNS3 LAB topology.I'm running a wsa proxy in a different vlan (190) which has a 10.1.190.0/30 mask, i have set up licensing and web proxy for via Port 80, 3128 and set it up in my test client. However ...
I'm writing a script to get mac-addresses of neighbors. It's in a lab environment with IOU images. I'm able to get the hostname of the connected neighbor, but can't seem to find the mac-address of the connected neighbor. Is this even stored in the M...
