Other Security Subjects

I would you to like if may per a host to setting connection timeout and xlate timeoutDue to some server software need more connection timeout by client request , So i want to configure specific server to extend connection timeoutIs possible , what co...

HI...We have setup a temporary isdn 128k connection to allow 50 users to connect to ERP (based on SQL) servers at the main site over citrix. We use a 1700 series router.The requirement is to allow these people to use only that application and nothing...

Hi ISP A is redirecting connections to my web server to a url of my other ISP BHow do I setup a translation on my PIX in ISP B's Colo to allow users on the inside to connect to the webpage.

hello,my PIX had reported the following message:Dec 22 08:15:11 192.168.47.254 %PIX-6-106015: Deny TCP (no connection) from 10.23.18.102/1035 to 192.168.50.214/80 flags RST on interface outsidei can't understand the (no connection) messagecan you gi...

Hello.When deploying a new configuration to the FWSM from the MC, all the sessions are teared down. What can I do so the sessions continue and wont be interfered ?Thank you.

hello everyone,i have 515e pix firewall and i want to take backup of the image currently my pix is having.i know copy flash tftp command,but i am not clear about the name of the image.i need some clarification.Arun Kachroo

Hello,I am running Pix IOS v6.3(3).I want to block snmptraps originating from a certain source. Just adding an entry to an existing ACL.My access-list entry is:access-list Inbound line 1 deny udp host 172.x.x.27 any eq snmptrapThis entry is at line 1...

Hi, I have not been able to find an answer to this question.I see routes on PIX deviced expressed 2 ways both seem to work.1) route outside 0.0.0.0 0.0.0.0 149.149.43.129 12) route outside Toronto 255.255.255.0 123.15.203.193 1What is the difference...

I have a Cisco 501, version 6.3 firewall. The modem of UPC (internet) gives no ip address to the 501, because the mac address which enabled the connection with internet is a network adapter in a standalone pc. UPC can only accept one mac address. The...

hi all...i already connect using isp 1 and add connection using isp 2. i put mail server on dmz port and permit tcp on 444, 1080, 8080, 80. but i cant't connect from isp 1 to mail server on isp 2. could some one give an answers.. thx

Does anyone know how to allow AOL Instant Messenger Live Video IM through the firewall?The AIM client allows you to set it up for a proxy server (Which I don't have), or says to open ports 1024 - 5000. I don't want to simply take down security in th...

Hi,I have PIX515 with 5.3. Currently I cannot get into the PDM because I forget the password.Could anyone tell me, how to add a name with password in CLI so I can use it for PDM?Thank youHendarto

Hi,We have done PAT for one VLAN. All the users (approx 50) in that VLAN accesses citrix port (1494) on the remote end server. Now few of the users can access citrix and load respective applications while the others are able to connect to the citrix ...

Has anyone had problems with using AutoCAD LT2002 once Cisco Security Agent (CSA) has been installed to PC/laptop ie LT2002 will not start and comes up with memory error message. Only way round this so far as know is to remove CSA.Any help would be m...

hi all,LAN1--R1----Internet----R2---LAN2LAN1 and LAN2 communicate over the IPSec tunnel, crypto map applied under the interface connected with internet, after apply the crypto map, I can not telnet the router, how to solve the problem?Thanks