Other Service Provider Subjects

Hello Every One .I have a problem with my internet connection. we have cisco 2911 router with 4 atm WICs , that connected to our ISP . the Problem is after ISP upgrade their infrastructure to MSAN , i can only get one dialer interface up and the othe...

Dears we have Cisco ISR 1100 c1100-universalk9_ias.16.09.02.SPA.bin we have problem on Cellular interface  it is working at startup normally , but suddenly it goes down and we get the following log %FMFP-3-OBJ_DWNLD_TO_DP_FAILED: R0/0: fman_fp_image:...

I am trying to replicate my Internet edge in my lab and I am struggling to understand how PEs are configured to peer with my CEs.For what I can tell the PEs are advertising the default route using the network 0.0.0.0 so I set this up and set up a sta...

I have ASR100x devices with ISG (iWAG) using multi vrf, services loading via Radius.Is it possible to use mdns routing features of IOS XE on ASR with that configuration? Or these features are incompatible (mdsn and isg)?

Hi all!Can anyone here tell me when IOS-XE will start supporting BGP large communities?Thanks a lot!Best regards,Thomas

Hi,Previous we were using Cisco 7606 as BRAS and the issue was Router keeps on rebooted automatically.OLD Details about Cisco 7606Router 7606 #show versionCisco IOS Software, c7600rsp72043_rp Software (c7600rsp72043_rp-ADVENTERPRISEK9-M), Version 15....

Some 15 years ago we had implemented a PWLAN service by deploying SSG on IOS and Cisco SESM (Subscriber Edge Services Manager) as the web interface (i.e. captive portal). Fast forward, SESM becomes EOL, gets replaced by Broadhop SME. Some years later...

Today we have a fiber ring that houses our Layer 2 traffic with a single egress to the outside world. I'm trying to add an additional that will be primary for the closest nodes off the ring and redundant for everyone else. The single egress is on an ...

I have made a very simple eem applet to monitor some IP SLA entries in near real time -   ! event manager applet AUTO_SLA event timer watchdog time 3 action 1.0 cli command "en" action 2.0 cli command "term len 500" action 3.0 cli command "show i...

Hi, I'd like to ask how to check via SNMP signal to noise ratio or number of codewords (without errors, with correctable errors etc.) on interfaces connected to CTMS via R-PHY shelf. So far, I've been using OIDs from DOCS-IF-MIB (like for example: do...

Hello,How can I verify status of license (Ten Gigabit Interfaces) loaded on secondary (standby) pre 5 procesor on my ubr 10k platform?Command show licence display info about primary processor:Index 1 Feature: WAN_LicensePeriod left: Life timeLicense ...

I am using Cisco 7606-3CXL with Sip-400 and due to hardware issue m going to change router to 7603-S (Available in market)But in router 7603-S  15Mpps  and in router 7606 is 30Mpps.i want to know that, how can i check in router 7606 currently mpps us...

ASR903 / RSP3 / IOS-XE 03.18.05.SP.156-2.SP5-ext Hi community members,I have a problem as follows. On a "normal" physical 10GE interface I have configured a parent egress policy which traffic-classes matchingon different service instances.I achieve a...

We're currently using CA Spectrum for a fault management system.  In 2017 we discovered that newer Cisco ISR's (ex. 4331, 4321, 4431) and ASR's (ex. 1006, 1002) are no longer supporting the CISCO-ENVMON-MIB on these devices running IOS-XE.  How we di...