Routers - Small Business

Hello, is it possible to set a DNS Helper so that i can use my central DNS Server? DNS-Server -> first RV345 -> WLAN -> second RV345 -> DNS Clients ThanksBruno

A client would like to migrate off PPTP to IPSec using an RV345 and the 3rd party VPN client option.  Does anyone know if there are any docs or instructions out there that describe how to enable this using the native Windows 10 L2TP/IPSec client?  I'...

Hi Guys, mi name is Pablo, and i have 2 Cisco RV345, in Firmware Version 1.0.01.20, and the same configuration in 2 routers (changgin only segment ip).I have a link point to point in port 16, for connect 2 branch offices.I crate a route static for vl...

Hello all, I have a remote RV130 set by a local remote ISP as "gateway" in the operating mode for "routing" under "networking" section.Simple configuration, Optic fiber, a WAN ip, a LAN ip, that's it.Everything works well except i can't connect my IP...

RV082: Static IP, no NAT, Firmware: v4.2.3.09   RV042: NAT   I've tried literally every setting on both sides. On the NAT side, I'm forwarding UDP 500, 1500, 50. Nothing will cause these two devices to connect. What else could possibly fix this?

Hi, I'd like to setup an OpenSLL connection for all internet traffic through to IPVanish using a private VPN, can anyone suggest how I go about setting up the router? Thanks and regards

Hello everyone, I placed a RV220W to a small site, Firmware 1.0.7.2, PPPoE, 2 Site-to-site VPNs, 2 VLANs, 6 wireless devices. However, this router going to drop the Internet connection in recent 2 weeks, 4 times per day in average. Try to google abou...

Hello All,   I got the RV340W for 2 weeks, and the 5 GHz wireless no longer broadcasting suddenly.   From the front panel LED, the 2.4 GHz WLAN is ON but 5 GHz WLAN is OFF. Both radios are ON in the Wireless Settings, and I checked the Radio Status f...

Hi, I have an RV130W router configured to establish a site to site connection.The tunnel perfectly establishes the connection, but every so often it reconnects and I do not know how to find out the reason.In the log I see the reconnection process but...

Hello!I have an RV340 (1.0.01.20) which does not apply the changes I make in Port Fordwarding. I need to create new rules but it does not work ... I make all the changes, but after I apply it, it returns the settings that were.I have already tested t...

We have a SAS model and get routers for testing and creating support documents for our customers. We recently got a RV320 for testing and I must say, this thing is about as cheap and worthless as they come. Not sure what Cisco is doing since I would ...

Dear Community, I came across a shortage of the RV340 that is rather shocking but I hope the reason is my lack of technical knowledge.I set up two VPN tunnels to one ASA.First connects the local RV340 Network 192.168.1.0/24 to the remote ASA network ...

Hi to everybody. I would like to ask if Cisco router 1802W supports  DUAL BRODBAND connections by using 2 WAN Interfaces ?1 X PPPOE1X STATIC IP Thank you !!

Hello, We have two office networks(192.168.3.1 and 192.168.10.1) connected through gateway to gateway VPN. We tried to configure static routing on the router at ..3.1 network to route packets to IP range 10.130.78.0/24 through gateway 192.168.10.1. T...

I have a load balanced dual WAN setup on an RV320, and I have one device that I need to exclusively use the WAN2 port, with all other traffic going through WAN1. I've set up the top priority protocol binding with the all traffic service, the device's...