Routers - Small Business

Hi, I'm having issue with Huawei E3276 dongle which supposed to be supported under firmware version 1.0.3.22 but i keep getting "card status: error" and i cannot get WAN connection up. Please guide me to resolve this issue.

I have VPN between WRVS4400 and RV220W. I had to change WAN IP address at RV220. So after that i cant establish VPN. (chenge VPN IP in WRVS).And: From WRVS computers i can go to admin RV220 with local IP, can ping to RV220, but cant ping to computer...

Hi, short story, I installed on a site a cisco 819G with pre configured working cellular 0 interface like WAN-2 Backup.  On site I finalyse the config for the WAN-1 primary. Working. The issues is that I did not test the failover on site , but now i...

Hi, I have been using 'dir usbflash0:' etc on a Cisco 1941 router with IOS v15.1 fine. Today I have upgraded the IOS to c1900-universalk9-mz.SPA.155-1.T.bin and also tried c1900-universalk9-mz.SPA.155-3.M3.bin. With these new IOS's I am unable to ...

We are using RV082 as our voice router and we bought RV325 as the possible replacement because the RV082 is on its end of life. We setup the RV325 with the same settings as RV082 but when we switched to it, we get a lot of reports of garbled sound is...

hi all, Sorry for my poor english but i m french. i search on many topics but can't get a helpfull response. i have recently buy a cisco rv320 routers. i have activate firewall and configure acl 1 - allow traffic from wan on port 21 (FTP) to an inte...

Because my provider (UPC, Swiss) only offers "DS-Lite" _or_ "IPv6 Only" I have registered an IPv6 tunnel at hurricane electric. I tried many configurations and searched for days now, is there a configuration sample for activating this tunnel in the ...

I am trying to configure Cisco RV134W to connect to my Singtel MIO IPTV service which runs on VLAN 20, 802.1p priority.  The Internet setting given by the ISP are: Internet:  VLAN 10 IPTV:  VLAN 20, 802.1p Priority 4 I have managed to get the Inter...

I am not sure but think it could be a software bug. I used Packet Tracer 7.0 doing lab simulation, I created network using OSPF as routing protocol, the network consists of three areas: area 0 and two non-back area, the connection between all routers...

Hello,  I was wondering if someone can email me the firmware VA_A_39t_B_38r1_24o_rc1_SDK_4.14L.04A.bin Thankyou james.m@iinet.net.au

I have a Cisco RV320 behind a Verizon FIOS router. I manually assign the RV320 an IP address in the same subnet as the Verizon internal LAN on the WAN connection. I setup Gateway to Gateway under VPN and under local security group, I select IP. No ma...

For almost 2 weeks, we started experiencing a problem with a new RV320 router.  The router was installed and has been performing well since January 2017; however, about 2 weeks ago we started to notice that webpages are slow to load. For example, loa...

Set up is as follows. Two Lans, each with their own Internet access.  Each have their own DHCP scope from comcast DLS routers. Lan1 192.168.60.0 Lan2 192.168.50.0 I've connected the Comcast router of Lan2 to the Wan1 interface on the RV320. Port 1 o...

Ich kann mich nicht auf die Konfigurationsseite für den RV042G verbinden. Obwohl der Router angepingt werden kann bekomme ich eine Fehlermeldung, dass 192.168.1.1 nicht erreichbar ist. Was kann man da tun? Gruß LB