I am trying to go from a layer 3 port and use three different bridges with vrf going to one vlan in a router going to another router with same configuration. I unsure of how to do this because all the documentation is for switches or is too old to be...
Forum Posts
Hello, I am facing issues regarding connectivity as I am fairly new to BGP and route redistribution.In my topology there are 3 autonomous systems with eBGP running between them, each AS is running iBGP and a different IGP. I am trying to redistribute...
HelloPlease refer below diagramWe are using the default-information originate on cedgesbut when DIA 1 is unreachable or i apply an acl with deny all on the isp interface still it advertises the default route in ospfIs there a way to use an ip sla and...
Getting slow speed while sending traffic gre tunnel with ipsec
Hi, starting something new here and seem to be having an issue. My FPR1010 is set in PPPoE Mode and obtains a Static WAN IP as its GW and I also have a block of 8 Static WAN IP’s (6 usable). I was trying to assign a DDWRT router to an Interface on th...
Hello guys,I need some help about routing between my core router and segmentation firewall.My topology: Asr920>iBGP>fortigate seg.fw>iBGP>perimter cisco frp with fmcPortchannel as trunk with service ethernet instacne to fw, allowed BDI.Comunication i...
HejI am trying to figure out how to configure an Aggregate route on IoS XR. I just couldn't figure it out. Thanks
Resolved! BGP Default route for two different ISP
Folks, I have two ISP terminated on my two distinct edge routers (Its Cisco Nexus 93180 Switch) from here its connected to Border Leaf switch which is connected to EVPN fabric. This is new setup so my question is can I connect both border lead switch...
I have typed below command, normally it has to let me enter yes or no but in mobaxterm when i press enter it is jumping to next line R1#, skipping Reset ALL OSPF processes? [no]:anyone faced this? pls help. R1#clear ip ospf processReset ALL OSPF pr...
After upgrading to 10.3(6) we are seeing the following messages ,%OSPF-5-NBR_RETRANSMISSIONS: ospf-<process id> [7644] Process re-originates LSA ID 1 LSA Type Network adv-rtr 10.42.42.1 in area 0.0.0.0 for Nbr X.X.X.X.As per the following, this is th...
Hey guys,I am super new to packet tracer and I have been tasked with creating a small network for my end of year project at school. I have 2 routers, 2 switches, and 3 end-devices. My network has 3 VLANs and I have been working away at this for about...
Hi,I had OSPF neighborship flapping which I have solved. However, I have few questions.The logs I kept getting were "....from full to down, neighbor down: dead timer expired.".The main culprit was ACL on the port with entry denying destination IP 224...
Hi IOS SMEs,I have set up a "Guest" network via second ISP connection.My primary network is via different ISP and has working BGP based routing, which advertises a set of Class C addresses and gets static route to ISP returned.The guest network is on...
We observed periodic is-is drops via the SRP interface c10720-ATS4 and, as a result, rebuilding of the SRP ring.There is a ring topology:ATS1 <-> ATS2 <-> ATS3 <-> ATS4 <-> ATS1 Connections between elements are organized via direct optical fibers.No ...
Hello Family, I have applied prefix-list and route-maps as below, ip prefix-list MEB-IN seq 15 permit 10.251.0.10/32ip prefix-list MEB-IN seq 20 permit 10.251.0.11/32ip prefix-list MEB-IN seq 25 permit 10.251.0.13/32ip prefix-list MEB-IN seq 30 permi...
