Hi,my problem is that there is a working openvpn connection to the RV260 (behind a FritzBox, port and route forwarding definitely works). Is is possible to connect from remote to the RV260 (via webbrowser login, the IP is 192.168.250.4), but i cannot...
Forum Posts
Hi, one of the customer wants to configure shaping qos on multiple port at one switch. As this switch roles HQ distributtion switch to mant branches. (HQ is multicast source) There are multicast stream and the customer wants to allow only 70% bandwi...
Hello Team,I would like to better understand of behavior of my QoS. I have configured class with priority, and then with police. Lower classes are configured with "bandwidth remaining percent" command.policy-map TRAFFIC-OUT-Gi0/0.7 class OUT-VOICE ...
Hi Experts. I have faced issue with module 3 before some days, below logs is generated on device and its looks like software but unable to isolate issue because kernal dump file is corrupt.. Need your help to find RCA. LC/0/1/CPU0:Apr 7 23:20:54.827...
How much routing capabilities do I have with lanbase? Meaning can I use floating static routes? ip route x.x.x.x x.x.x.x 10.0.0.1ip route x.x.x.x x.x.x.x 10.0.0.2 200 ---- Will this work I have tested and it doesn't seem like that will work. H...
Cisco ISR 4331 on boot up I receive this alert: %IOSXEBOOT-4-BOOT_SRC: (rp/0): WARNING: Attempting to use bootflash for packages storage! This is after moving from ios 16.6.4 to 16.9.3.we had to make this jump in order to utilize the boost performan...
I setup a site to site vpn by 2 rv340 router. One side use static IP and other side use dynamic IP. After vpn established, I can ping 2 routers(192.168.0.8 and 192.168.0.2) in HQ site from remote site (192.168.25.1), but the server (192.168.0.36) can...
Hello, We have roughly 50 1941 Cell routers in our environment. For the past 3 months ,once a month, they have all went down at the same time, and came back up at the same time. The outage was roughly 1 minute long. In each router, they all say the ...
interface Loopback6 ip address X.X.X.62 255.255.255.255 Router#sh ip access-lists Extended IP access list 199 10 deny tcp any any eq telnet 20 deny tcp any any eq www log 30 deny tcp any any eq 22 40 permit ip any any (52 matches) E...
HelloI have a wan modem connected to a Cisco RV130 and enabled pptp VPN.I can establish a secure connection though the WAN modem into the device via pptp. I can ping devices on the LAN side of the RV130. I can open local web pages for the configura...
Hi, I would like to implement RSVP into this network (Image below to help understand) however i have no previous experience with RSVP and have never configured it before. I would like to configure RSVP to benefit video streaming on the network Seria...
Hi, I have 2 ISP's. Cisco 3825 router and Cisco 3750 as core switch. WAN SIDEHave terminated both ISP's in Cisco 3750 on different Vlans (101 and 201). From there made a trunk of both vlans and connected it on Cisco 3825 by making sub-interfaces. L...
AnyConnect is working but I can't access the web server but ping works. Attached is the full configuration. I had to remove the nat to get it to work.((( no nat (inside,outside) source static 192.168.172.0_24 192.168.172.0_24 destination static )))...
Resolved! vrf router controll
hi friens i have a question there is s imple topology PE1 <------->P<------->PE2on both PEs i configured vrf vrf_alet us use PE2 as an exaplPE2(config-vrf)#do show ip rou vrf vrf_aGateway of last resort is not set33.0.0.0/32 is subnetted, 1 subnets...
Hi everyone. I have own public ips and ASN and configuration BGP everything is ok. I can go to internet with my own IP. But when I want nat my internal subnet to my public ip and go to internet or do static nat not working. I want configuration nat o...
