Hi,I have google and asked many ppl about what does the "threshold" refer in the track command, but i still cannot understand it.Would u give me some explain by a this example? Thx very much.for example: track 10 ip route 10.2.21.128 255.255.2...
Forum Posts
Hello, We are having trouble testing an HA Scenario with a Static NAT configuration on a pair of Cisco 4351 ISR. A redundancy group has been created, the inside and outside interfaces has been assigned with the redundancy group and the static NAT's w...
Question, When doing an activity search, is there a way to tell where the user went and what was served up automatically by the site? A good example is when user keys in www.msn.com, just from that one entry, the user gets many additional entry for a...
I have a Cisco ASR 9006 chassis running 5.3.4 with the following line cards: A9K-RSP440-TR (Typhoon) A9K-24x10GE-TR(Typhoon) A9K-8T-L (Trident) I need to add a A9K-8X100GE-TR (Tomahawk) to the chassis. We have other routers with 5.3.4 and a mix o...
Resolved! Strange routing issue
Hello, I've run into a strange issue that I can't wrap my head around. This issue is not causing any impact, but I don't quite understand it. If you look at the picture, that is what the network looks like. On core 1 of Datacenter 1, when I do...
Hi All, I am having trouble with equal cost load balancing. I am trying to ping host with IP 10.0.10.11 Below are the routers that I am trying to loadbalance. But almost all off traffic is going out Ethernet0/1 only even though they are with equa...
I referred BGP path selection algorithm from below link https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13753-25.html Can someone help to understand why Step #10 is only for external peers? Why is this rule not applicable ...
I have a config that I am trying to bring up, and in my mind it should work, but perhaps I am missing something. The idea is that one end of the link is a layer 3 interface on a router. The other end is a switchport trunk, on a vlan with an IP inte...
I currently have SDWan deployed in my environment, sitting behind the edge router(s) and it works great! Aggregation, fault tolerant, optimization,etc. However, it cannot forward inbound IPSec traffic to my SSLVPN appliance. Can I route 1of my exte...
Hello, I have Cisco 887v router with C800 Software (C800-universalK9-M) Version 15.3. My Scenario i have a ISP-1 with cable modem another ISP-2 with static WAN route. I want ISP-1 for IPsec VPN and ISP-2 for default internet. PLEASE HELP ME...how ...
I have just installed a CSR into Amazon AWS and have a query on routing between VPCs. There is a Public VPC with the CSR Outside interface in and a private VPC with a test server. The CSR is fully integrated into our private DMVPN and that side see...
I have a GRE over IPSec tunnel that gets high bandwidth utilization every 2-3 days and stays like that for 2-3 days. I look at the traffic using netflow on the 2811 router and 95% of the packets in and out are either GRE or IPSec. I only have two t...
Resolved! 2 Wan 2 Router IPSLA PBR
Hello, i have 2 router 4321 and 2 ISP, R1 have ISP1 R2 have ISP2 how i configure failover for this setup not just link but device failover. thank you
Resolved! Cisco 2621XM Router IOS Booting Issue
Hi All I was wondering if you can help me out, I have loaded ios c2600-ipbasek9-mz.124-25a.bin on the router, for some reason it boots twice as you can see details below, it says %SYS-6-READ_BOOTFILE_FAIL: flash:c2600-j1s3-mz.123-26.bin File boot fai...
I am able to get an ipv6 /64 address from Xfinity with no problem however I have multiple subnets I need to cover with ipv6 so I'll need a /60 or lower. How do you specify the DHCP-PD request for a /60 in the RV340 so that I can break up into a mult...
