Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

 
Labels

Forum Posts

Hi ciscomates! I have a doubt about licence performance into 4451-X, What is the meaning of 1 Gbps performance? I think that the maximun throughput that I can achive in total, adding each interface throughput. In example, If I have a router for routi...

david.sua by Beginner
  • 1892 Views
  • 4 replies
  • 0 Helpful votes

Hi I have a Cisco Catalyst 4510 R-E that requires a password recovery how do I go about removing the password I have the following cards installed 2 x WS-X45-SUP6-E  Supervisor engine 6-E1x WS-X4624-SFP-E1x WS-X4648-RJ45V-E Thanks

Hi All, We have TWO MPLS circuits on same PE of same customer with two different vrf's X & Y but import and export RT are same. Please see below configuration and outputs. There is a route in X VRF 192.168.26.0/24 which is not being leaked on to Y vr...

Hello,We have a /22 internet address block. We devided it into four /24 address blocks, say, A, B, C, and D.ISP "Z" is the only ISP we peered with via BGP, and address block A has been distributed thourgh them.We have only one AS number.The company p...

ayao by Beginner
  • 1125 Views
  • 4 replies
  • 0 Helpful votes

Has anyone done BGP peering w/ an ISP, and received prtial routes w/o any problems?We're thinking to do this on a 3650 switch, and weren't sure if it has enough resources to hold the partial routes.How much memory does a route take?3650 has 4GB of RA...

Kevin-H by Beginner
  • 1220 Views
  • 7 replies
  • 0 Helpful votes

Hi,I have 2 SSID broadcasting from the same radio and want to ping between them. They each have their own VLAN and DHCP pool but, I cannot ping between devices connected on each. Is there someting more I need to do in order to do this?I'm using a 194...

Ed Lo by Beginner
  • 229 Views
  • 3 replies
  • 0 Helpful votes

Hi Community, I'm trying to setup NAT for the following scenario with no success so far.  I need machine 10.5.2.33 to communicate with 189.23.0.85 and vice versa.Only RT1 "knows" how to reach both sides. I almost managed to have this working with the...

nat_issue.png
pmarques by Beginner
  • 721 Views
  • 5 replies
  • 0 Helpful votes

Hello,I have a router and router pid ISR4331/K9In my router when I enter the command "show proc memory sorted" and the output is below...ABP_Atcis_GE#show proc memory sortedProcessor Pool Total: 1688360784 Used: 311830448 Free: 1376530336lsmpi_io Poo...

sukhendra by Beginner
  • 3544 Views
  • 2 replies
  • 0 Helpful votes

Hi all,   Im planning to prepend my AS to my 2nd ISP, like i have ISP-1 = 100Mbps and ISP-2 = 50Mbps so that my inbound traffic will come over to my ISP-1. What if my ISP-1 get congested will BGP behave to force other traffic to my ISP-2? or should i...

Hi all,  i found a site regarding aggregating routes, Credit to packetlife R3(config-router)# aggregate-address 172.16.0.0 255.255.248.0 as-setR4# show ip bgp BGP table version is 12, local router ID is 10.0.0.10 Status codes: s suppressed, d damped,...

Roel Reyes by Beginner
  • 1388 Views
  • 2 replies
  • 0 Helpful votes

Resolved! COS to WAN ISP

Hi there,Thanks for reading.My ISP is dropping packets from our BE COS queue.  I just found out we're not marking properly and only 10% of our traffic is in the correct COS queue.  Based on legacy requests, the ISP has COS2 set as highest priority.  ...

Bob Greer by Enthusiast
  • 490 Views
  • 5 replies
  • 0 Helpful votes