hi guyscan i configure network id or broadcast id on cisco router interface e.g 192.168.0.63/26 can i configure this address on router's interface
hi guyscan i configure network id or broadcast id on cisco router interface e.g 192.168.0.63/26 can i configure this address on router's interface
Can anyone tell me how to enable the SFP module on cisco 2921?
When I create an acl, then copy/paste it into the router, my 'remarks' don't stay in the same order. Why is this happening and how can I fix this? Attached are two text files; copy/paste from a text and what the order looks like on...
I have a big issue, a route reflector is routing paths to none clients and it should not be routing paths cause it is configured as route reflector!! Help me outSent from Cisco Technical Support Android App
hi,we have this hub and spoke setup, so each spoke connects to 2 hubs. then with eigrp we decide which hub gets priority. simply by using an offset list and saying any route you give to this hub1 and learn from it add 10000000 to the distance so this...
Hi Folks,really confused on following BGP path selectionsBGP routing table entry for 1.0.16.0/23, version 18808717Paths: (3 available, best #3, table default) Not advertised to any peer Refresh Epoch 1 1174 21914 22519, (received & used) 140.60...
The prefix 100.179.12.0/24 is learnt on tap via eBGP and eigrp..i have set bgp backdoor command so that IGP wins over BGPBut it looks like even after hard reset, isn't working. can someone explain if i miss something here?tap#show run | s r bgprouter...
I am trying break into a Cisco GSS 4490 because the previous administrator didn't leave the password how can I accomplish this?
HiI am new to bgp please help me out troubleshooting this issueMy topology consists of 2 edge router one with evpn as primary and dmvpn as secondary. And have two 4500 core switches running ebgp between both the edge routers and ibgp between both the...
Any help with this issue would be greatly appreciated.ip address 172.15.45.2 255.255.255.0ip nat insideip virtual-reassembly induplex autospeed auto!interface GigabitEthernet0/1ip address 172.15.45.1 255.255.255.248ip nat insideip virtual-reassembly ...
Am applying a policy map to gig0/0interface vlan xIf i apply to either one only it is ok but if i apply it to the other interface it says ''configuration fail''.Am not also given the option to apply it to a particular interface as the one below servi...
Hi,Am wondering if it is possible at all to configure source or policy NAT on the router like the one on ASA ?ThanksRegardsArunas
Is there any particular reason that OSPF refuses to send default route from the ABR to the remote site? The command "area 123 stub no-summary" does not do the trick, the remote router will not receive the default route. Note that this works perfectly...
Hi All , As per attached diagram , EIGRP is configured between Wr01(router) to Sw01(switch) and Wr02 to SW02.IBGP is configured between Wr01 to Wr02 (connected back to back) and trunk link is configured between Sw01 and Sw02.EIGRP to BGP and vice ver...
Dear Guys,i have problem with device. The device Nexus7000 C7010 with System version: 4.2(1) is suddenly reload .this is cause from sh system reset-reasonCORE1-7010# sh system reset-reason ----- reset reason for Supervisor-module 6 (from Supervisor i...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
03-07-2025 07:44 AM | ||
03-06-2025 12:48 PM | ||
03-06-2025 07:14 AM | ||
03-05-2025 04:09 AM | ||
02-27-2025 04:10 PM |
User | Count |
---|---|
13 | |
8 | |
5 | |
5 | |
4 |