Hi,I created a vlan because our Ip address range is running out. The network is working internally. But i want to step an IPsec tunnel for our azure. The Vlan can't access azure virtual machine. Is there any way to create an IPsec tunnel with that vl...
Forum Posts
I have 3 Vlans on my network Vlan 1 = 10.76.x.x Vlan 2 = 172.16.x.x and Vlan 3 = 192.168.x.x, my question, I noticed that my loopback addresses on the switches are on the 192.168.X.X network and I wanted to use that for my Vlan 3. What is the best Pr...
GIVEN: (obfuscated) NEXUS-9300# sh ip int br vrf allIP Interface Status for VRF "default"(1)Vlan30 172.16.1.5 protocol-up/link-up/admin-upVlan172 172.17.2.2 protocol-up/link-up/admin-upVlan200 172.16.3.8 protocol-up/link-up/admin-upVlan300 172.16.3.9...
Hi,I have configured BFD on 7609 router and other remote end is Huawei. But BFD is not getting UP. Following are results at my side. Can any one help in this case. NeighAddr LD/RD RH/RS State Int58.27.222.70 ...
Resolved! Status Static Routes into IPSec VTI
I need to create a static ipsec VTI (on ISR4k/IOS-XE) which will connect to a Fortigate at the far end. DPD is switched off at the far side and I don't have any control over it. The tunnel will have a static route /24 pointing towards it and this wil...
My customer needs fax support on the router so ordering FXS port. Do we need add PVDM or it is built-in like 4K router?
I cannot get the firewall to provide dhcp after trying several options. I tried using it as the ip router, the default gateway with no success unfortunately. I would prefer getting it from the DC but management wants it strictly from the firewall.
Hi all, Looking to create an inbound route map which increase BGP AD distance of the subnets shown below so that the EIGRP route is preferred. What is the configuration needed to amended the BGP route on these subnets to say 175 so the 170 EIGRP rout...
In Packet Tracer, I have two routers, R1 and R2, which are connected to each other through R1's g0/0/0 interface and R2's g0/0/0 interface. Both routers are correctly configured with IP addresses and OSPF. On R1's g0/0/0 interface, I entered: ip ospf...
Hi I add in my cisco ASR 1001 PPPoE Server Open Fiber POPs vlans.Every Open Fiber POP must have a VLAN assign to my KIT. Every customers living in the city behind the POP, will have a customer vlan for reach connection.How can I add multiple customer...
I am running a Ciso ASR 1002 with ASR1000-ESP5 RP and version ASR1000 Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 15.4(3)S6a, RELEASE SOFTWARE (fc2) as an outward facing internet attached router. I am using the zone-based firewall and the ...
Hi, i am trying to understand how vrf, rd, and route-target import/export works. I have this simple topology and i am running iBGP between the routers in vrf 865, neighborship has been established and i have configured same rd and route-target on bot...
I have a network in Packet Tracer 8.2 that looks like this: All of the interface addresses are configured correctly. My OSPF configuration on R1 is: router ospf 1network 209.165.0.0 0.0.0.255 area 0network 192.168.3.0 0.0.0.255 area 0 My OSPF ...
hi I am trying to find "no dynamic routing" command for IOS xe, this command is not running on iosxe so do we have an alternate command?
Hello people of Cisco. I have a question. I've tried working this out for several god dang hours but I just can't figure it out. I don't know what the problem the assignment is hinting to, is... I've tried changing IP addresses, put on codes (if it a...
| User | Count |
|---|---|
| 12 | |
| 12 | |
| 7 | |
| 6 | |
| 5 |
