Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! WAN Access for Switch VLANs via Router Config Examples

Hello Forum,Hopefully this is the proper channels for this type of request.  I have a customer who is looking for some online documentation that shows the configurations needed to accomplish the following:They have a L3 switch (3560-E) where all thei...

derrwill by • Cisco Employee
  • 960 Views
  • 2 replies
  • 0 Helpful votes

L3 switch multicast range

hi Cisco Pro's,what if am assigning an IP address to a device let's say 10.10.10.10/24 and i want the multicast to be like this 10.10.10.11/24 ( note the increment by one of the multicast IP last octet when compare to its last octet of the unicast IP...

100mbps of encrypted traffic

Hello,Which ISR G2 is appropriate to handle 100mbps of VPN traffic? would 3925-sec/k9 suitable for this?The Cisco docs are very confusing on this matter... and couldn't find any reliable information.

Tkacprzak by • Level 1
  • 1402 Views
  • 5 replies
  • 0 Helpful votes

Cisco Wan Manager 10.5 question/problem

Yes this is very old, but I hope someone can help me out here.  Lost a disk that had CWM 10.5, Informix and the Informix raw partitions(don't ask me about the build, I inherited it) on it.  New disk, recreated everything, restored CWM and Informix fr...

Resolved! Keep VLAN Tags between 1921's over T1?

I must be doing something wrong.  I am looking to transfer 3 VLANS (10, 20, and 30) over a T1 point to point using Cisco 1921 routers.  I do not want to "Bridge" the connection, one location has a 10.1.0.0/16 subnet and the other location has a 10.2....

ADynes by • Level 1
  • 3830 Views
  • 17 replies
  • 0 Helpful votes

Cisco 7204VXR OC3 Output drops increasing

Hello Team,Any idea why my OC3 interface is showing increasing output drops its starts happening as soon traffic exceed 60Mbps   ( FYI my traffic never exceeded 75Mbps MAX, and circuit is 150Mbps from carrier , full OC3)Any thoughts how i can fix th...

ahmad82pkn by • Level 3
  • 4114 Views
  • 17 replies
  • 0 Helpful votes

BGP route selection using weight

Hi , I'm trying to do lab with  BGP  route selection using weight, my purpose is to apply weight in edge router  for specified incoming prefix (41.10.10.0/24) with neighbor 66.10.10.1 , the config of edge in attached document I the result of sh ip b...

DDR as backup. No idea how/when it should work

I'm checking some config with backup analogue line configured as DDRSh dialer shows dial string and status idle.How can I check when this dialer trigger from idel to active?There is no other interface looking external, but there is HSRP configred bet...

output drops other than by RED

if using RED/WRED for congestion what else would cause output drops. i ask because i have a higher number of total output drops than I do with RED drops. Basically why im I not seeing the other drops, supposedly i have 719 drops but only 421 by RED, ...

Resolved! Cisco 1941 with IP Base License

Hi,I currently purchased, Cisco 1941/K9 with 2 onboard GE, 2 EHWIC slots, 1 ISM slot, 256MB CF default, 512MB DRAM default, IP Base.Questions1. With IP Base License, will I be able to run Frame Relay? I really need reference on what works and what do...

Cisco 837 Features

HelloI have some questions about Cisco 837. I couln't ding a good datasheet for that.1- Does Cisco 837 4 port ethernet switch is a managed switch? 2- How many VLANs does it support? 3- Does it supports EIGRP and OSPF anf BGP?4- Does it supports SVI?A...

Load more
Unanswered Topics
View All