Sorry if this is a long post but i'm racking my brain against the wall here. I have a strange setup where the building owns the router and they have cables throughout the house and provide us with a switch only. I decided to put a cisco C841M-4X-JSEC...
Forum Posts
Resolved! DMVPN
Hello Cisco,DMVPN is not a cisco propreitary.? From my understanding it is but i have recieved views from others saying it is not. Can you please clarify my doubt.?Thanks,Srini
HiI have idle sessions on a 3640 and I have tried the disconnect session number, the username, the ip address, but no luck.As can be seen from the below some sessions have been connected for weeks now. Is there a command I can use without reloading t...
Hello experts,I have some confusion with packet counters from "show policy-map interface". I don't understand, where counters just showing the hits on class and where actually packets which were processes by policy-map. Below is example of the show c...
Hi All,Im facing issue in establishing ibgp between routers. Could you please help me with the configuration.Need to estabilish ibgp between (1) R1 and R2 (2) R9 , R10 to R1 , R2i have configured HSRP on R9 , R10 and R1, R2 and configured ibgp using ...
Hello guys, looking for some advice for manipulating inbound trafficCurrently my network have 2 different ISP with 3 different AStopology :The goal is all traffic is going through AS 4761 and 17922 since it has higher bandwidth while AS 141125 only s...
Hello I have a 3560 switch with ip routing enabled.On VLAN 1 network is 192.168.4.0/24 with ip at 192.168.4.1 and there's a WAN gateway at 192.168.4.2.I've set `ip route 0.0.0.0 0.0.0.0 192.168.4.2` and so I can use that gateway if hosts on 192.168.4...
Resolved! CISCO ISR 4321 SSL VPN (WebVPN) issue
Hi Experts, I am trying to configure anyconnect on Cisco ISR 4321 but somehow the command is not being executed and I am unable to enable WebVPN command . image with ISR_4321_Security License enabled ^ It seems the ...
Hi all,is it possible to synchronize to an NTP server behind a static NAT? I keep getting this error:I have been unable to find anything Cisco-related to manycast.When I eliminate NAT there is no NTP sync error.I have the following topologyI am worki...
Hello Everyone, Hope everyone is staying safe and healthy. I used to have this line configured on an extended ACL:permit udp any any eq bootpc bootps But then a few of my laptops started having issues and could not get an IP address. So after many...
Resolved! STATIC ROUTING
Hello Above is the Topology in which there is 1 ISP with Two Sites. One Site is Connected with WAN IP(10.0.0.0/24) with ISP and other Site is (20.0.0.0/24). Site 1 is having Loopback(1.1.1.1) and Site 2 is using (2.2.2.2). Routing Config :1. Made Sit...
Hello Everyone, I'm trying to work out a BGP design that talks to 3 different ISPs and 2 VRFs on a single L3 switch. I've been working this out for days in my CML lab with some minor success but I'm starting to wonder if what I'm trying to do isn'...
Is there a IOS/NX-OS command to show routes that use specified gateway or interface? (If there's more than one gateway , then show ip route | include gw_ip is not useful because printout is split over multiple lines.)
Hi all, I'm a student (so please don't roast me too hard ;)) and our class has, for a while, been working on VLANning with VLSMing. Until recently I haven't struggled a lot with it, but I've found that now that there's several switches in the mix, I'...
Resolved! 1 Router 2 WAN links to 1 ISP with HSRP
Hello Everyone, I am having some difficulties with the following. I have 2 WAN ports to the same ISP where I need to configure these two ports as Primary and Backup with HSRP. Each interface has its own /30 subnet. Now I am comfortable with LAN side ...
