Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
Labels

Forum Posts

Start a conversation

Resolved! Guaranteed Bandwidth

Hi2AllWithin our main Organization we got two divisions with separate LAN & WANBoth these division are on the same floor. Internet Service Provider provided one Ethernet cable with 10MB and a public range /29How do I gurante 5MB of bandwidth to each ...

Simple 1841 Config

/* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-par...

Resolved! HWIC-3G-HSPA or HWIC-3G-HSPA-G ?

Dear All,Would you please help me to choose between HWIC-3G-HSPA and HWIC-3G-HSPA-G?From the data sheet (http://www.cisco.com/en/US/prod/collateral/modules/ps5949/ps7272/product_data_sheet0900aecd80600f41.html) I can see that the only difference is t...

Resolved! Two VLANs -- can ping only in one direction

Hi experts!I have a Cisco 881w router, which has a built-in WLAN module. Technically it has to be configured as two separate devices with two separate VLANs and subnets (one of each for WLAN and one of each for LAN). So, I have used default VLAN1 for...

Resolved! Can a Catalyst 2950 switch be connect to a Cisco 1841 router to distribute internet?

I have a small wireless isp. I have been trying to connect a catalyst 2950 switch to a cisco 1841 router which is connected to a t1 line. It is a managed router from my t1 provider. The 1841 has a static ip of 12.xxx.xxx.129  255.255.255.128 and a la...

wan failover with vpn

Hello all,I have a question about a merged configuration which I attempted to get working recently with no luck. Our organization has a 1841 router which is it's primary router to ISP#1. This was a T1 connection which was being overworked by all of o...

PDU or routing issues

Hi,When i try to ping my router i get the U caracter :>>Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 80.125.46.36, timeout is 2 seconds:U.U.USuccess rate is 0 percent (0/5)>>but i can access via telnet to this device.Does someone k...

Ayad by • Level 1
  • 615 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Policy based routing.

Dear i have some doubtsI have two isp and connected to core switch and in core switch i connected bluecoat for proxy.   And I have 8 vlans.The issue is that i need to block internet without proxy, if any one want to access internet it should goes thr...

QOS question

Hello All,This might be a silly question but i need verification. Given the configuration belowClass map realtime (match any)match (real time voice/vid traffic)class map important (match any)match (potentialy bandwidth hungry applications (http/ftp -...

merryllem by • Level 1
  • 494 Views
  • 1 replies
  • 0 Helpful votes

2801 Router

I have just installed a CISCO 2801 router at a remote location with two T-1 lines (see config below)interface FastEthernet0/0 ip address 192.168.69.129 255.255.255.128 duplex auto speed auto!interface FastEthernet0/1 ip address 192.168.69.1 255.255.2...

dacruzer1 by • Level 1
  • 655 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Forcing a single subnet in and out one BGP peer

I have been reading all over trying to learn as much as I can about routing a single subnet in and out a single BGP peer but I am running out of time.We have a single 6500 with sup720 running BGP between 2 ISP peers. We advertise all out subnets to b...

9 Meg IMA

I have a 2811 ISR running 12.4.11 T4 IOS and need to configure it for a 9 meg IMA.I can get all of the interfaces to work but not as a Full 9 Meg.Either as 2 - 4.5's or 1 - 6 and 1 - 3 MegIs there anyway to get them to work as 1 - 9 Meg IMA?2 - ATM/A...

Load more