Buy or Renew
Buy or Renew

Routing

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Labels

Forum Posts

Start a conversation

Simple Frame Relay doesn't work

There is my simple network on the picture. I've also attached some show and debug commands.Line protocol down at the DTE end, and line protocol up at the DCE end. LMI types agree with each other. Debug frame-relay lmi at the DCE end gives following l...

kondratev by • Level 1
  • 563 Views
  • 4 replies
  • 0 Helpful votes

Multilink or teloc ??

Hi,We have 2 serial T1 AT&T links configured for MUltilink. The site was working fine till now. No changes done on the router.Now we are unable to reach the router. Got the circuit tested by at&t and turned out to be clean. Dailed into the router and...

Multicast

Multicast feed when delivered to trunk interface is it going to have multiple copies of the same traffic.I mean bandwidth will be multiplied based on number of vlans.

tahseen12 by • Level 1
  • 417 Views
  • 3 replies
  • 0 Helpful votes

Resolved! OSPF- playing with wild-card mask

Hello every1,I have got different IP addresses (of /29 networks) which are mentioned below. I have to add them in OSPF... one way is to add all the networks one by one ... however to avoid lengthy commands,i would prefer to 'summarise' the networks (...

Resolved! ATM link erroring

we've been working to isolate what has been causing the errors on the WAN.It has been tested to the DSU clean.Can please someone check if there's any possible issue with the config?It's aDS3 link.Thanksversion 12.3service timestamps debug uptimeservi...

jsheriony by • Level 1
  • 1451 Views
  • 17 replies
  • 0 Helpful votes

Multiple Routes with 2811

I would like to establish if a 2811 has the ability to manage and route traffic via 2 connections.We currently host a number of hosts in a datacentre and the defualt route is provided via an ethernet connection. We would now like to include a second ...

dns-admin by • Level 1
  • 343 Views
  • 2 replies
  • 0 Helpful votes

Problem wit configuring Access Server

Hi All, I'm configuring an access server but faced with the following problem.R1(config)#ip host r1 2001 201.201.1.1R1(config)#ip host r2 2002 201.201.1.1R1(config)#ip host r3 2003 201.201.1.1R1(config)#ip host r4 2004 201.201.1.1R1(config)#ip ...

newnetman by • Level 1
  • 675 Views
  • 7 replies
  • 0 Helpful votes

Resolved! 1811 Memory Running low

I have a relatively new 1811 router and it seems like every other day the memory is completely full and no one is able to transfer any data on the network until it is restarted. The unit has the standard 128 MB ram running IOS 12.4(6)T10. Any sugges...

mcast from neighbouring PIM domain

All, pls help.We have mcast data coming to us from other domain (no control and unlikely they will change smth for us). Our router is configured as a PIM-SM leaf router restricted to SPT and configured with static RP. We want to distribute that data...

cisco SDM

I want to know about sdm ios support and how it works, please, a will take the ccna 640-802 test and i need information about the test, any tips?? thank you!!!!!

m-garay by • Level 1
  • 611 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Hub and spoke frame relay enviroment for lab

Hii am trying to set up a frame relay hub and spoke topology in my home labi have two 2600 routers with wic-1t cards and a one 2520 frame relay routerMy question how do i connect them physically back to back with a db60dce/dte cable to make a hub and...

Load more