Routing

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

Labels

Forum Posts

Hi allI am looking to manage a few 3COM 4400 switches with SNMP and I would like to know the OID for the obtaining the Switch CPU as well Memory Usage. If anyone can give details and if possible the MIB file it would be helpful. Thanks Vijay

I have a NAT configuration issue which I can't seem to easily (more specifically cleanly) solve. I need to implement NAT at several customer locations due to IP overlap with other customer sites (we have no control over their IP space). Please cons...

I had menegitis a year ago and have some memory loss and can't remember how to set the OSPF area.How do I choose the OSPF area? I have about 35 OSPF areas active on different routers, mostly frame-relay.

Dear experts, Iam facing a problen in point to multipoint . 1)iam having head office in hyd and branch office in bombay and delhi.We have 2 links on vsat and 2 links on leased line(v.35)and vsat is RJ-45. Now we want vsat is primary and v35 is second...

Hi,we config the bgp to influence inbound traffic. the config is following. We would like 202.x.7 come in PA (provider A) and 202.x.10 come PB (provider B). In US site, we have one Internet circuit. we find that four ip address always goes to "provid...

leungcm by Level 1
  • 1063 Views
  • 5 replies
  • 0 Helpful votes

I'm considering to put two cisco 2811 router as BGP edge peer router in to operation in one of customers location. The conectivity from customer to provider will be up to 10 Mb. There will be no default route and the full internet routing table shoul...

Namsys by Level 1
  • 1680 Views
  • 5 replies
  • 0 Helpful votes

Hi,I have an MPLS network and a circuit that is 1.5 Mbps. I do not believe that I am receiving the full 1.5 Mbps speed on my WAN circuit. I want to complete a test on my own to determine the bandwdith on this circuit. I want to make sure that I a...

mdargin by Level 1
  • 762 Views
  • 1 replies
  • 0 Helpful votes

Hi,I have a Cisco 2821 Router which support one NM module and where I have insered two port Channelised E1 Card (NM-2CE1T1-PRI). But now I need to terminate one more E1 ( Channelised) in this router. Does VWIC2-2MFT-T1/E1 or VWIC2-2MFT-G703 card supp...

How much bandwidth does this modek cisco 2611xm series router support1.it has 2 fas eth connections and 1 wic slot with 2 serial ports( which iam not using )2. planning to take 4E NM card for this router to support my LAN traffic and want to use two ...

vepachedu by Level 1
  • 327 Views
  • 1 replies
  • 0 Helpful votes

I am having an issue with my DSL connection and my 1841. The DSL line is a 3MB connection, if I connect directly through my laptop I can run a speed test and get 3MB. Once I put the connection to the 1841 my speed runs any where from 400K to 545k. Ca...

Hi everyone,I run into some unknown problems when doing simple PPPoE configuration. When my dialer get's ip address it's disconnects in next few seconds and start ppp negotiation from begining. Here is debug below with ppp negotionaion and sss events...

Hi,I have a 7600, sup720-3B, 24SFP blade, 4 10G ports blade, running 12.2SXF7 and I have the following problem with this machine: one of the vlan interfaces is passing arround 4.5Gbps of traffic. Whenever the traffic jumps over 3-3.2Gbps all the snmp...

Can we have HSRP with Load Sharing between the 1721 and 1841 routers?Are any extra modules or interfaces required?We have been told that we can do HSRP between the 2 routers with NO extras required. But by having Load Sharing it provides us with som...