Routing

Hello All,I would like to give-up the Interview in next few days / months for a technical change over.Can any-one advice me what all "Preparation Steps" required to make Successfull. Today i am working in a BGP with MPLS environment includes OSPF als...

One of the major problems that i face alomost every day , is the problems with the WAN links. My network is based on leased lines. When i face a problem with a link i try to correct the problem by wathing the status of the serial links. Some of my ac...

Hi,I have a pool of IP address to reach my ISP ip route 0.0.0.0 0.0.0.0 200.14.145.13ip route 0.0.0.0 0.0.0.0 200.15.128.26ip route 0.0.0.0 0.0.0.0 200.110.123.140ip route 0.0.0.0 0.0.0.0 200.110.109.14ip route 0.0.0.0 0.0.0.0 200.109.115.7all of the...

Hi all,I've been using the following config for ADSL backup to a serial line, however it seems to show strange behaviour.interface ATM0 no ip address no ip mroute-cache no atm ilmi-keepalive dsl operating-mode auto hold-queue 224 in pvc 0/38 encapsu...

Hi,we would like to announce routes to provider A and B. detail please refer following.for provider A200.1.0.0/23200.1.2.0/24200.1.3.0/24 for provider B200.1.0.0/24200.1.1.0/24200.1.2.0/24200.1.3.0/24We find that, we always anounce 4 routes to provi...

HI, i am a lil confused...we have a Crypto ipsec / isakmp VPN tunnel setup from one router in the head office(loopback address) to the other router at the branch office(loop back address).Ospf routes are also configured.. and hello packets are being ...

I have a remote site that is connected to my NY office via Sprint MPLS using what they call a halt-tunnel. I have a redundant circuit installed with a PIX at the remote location and set a default route on the router of the primary circuit using 3 as ...

I am installing Ciscowork Wan performance utility 2.0 IDU 4.0 but while installation it is ask for installation of ciscowork commen service 2.2 .Can anybody tell me the link for ciscowork commen service 2.2.

We have recently been purchased by another company. They need to connect to our hq from two of their remote sites. They will be dropping two lines from two different providers to our hq. One line is a 100mb line that will be optical (fiber), the othe...

Hi all. I have users that are experiencing loss of service very intermittently without our HQ losing ping to the router. A sh tech produces the following on E0.FastEthernet0 is up, line protocol is up Hardware is PQUICC_FEC, address is 0001.422c.7...

Dear all,I am wonder if full wire rate can be support in Switch. For example, for WS-C2960-24TC-L, there are 16Gbps switch fabric. Can each of 24 ports can full wire rate? How to calculate? Thanks

Hello All,Need Very good recommendation for Understanding, Implementing, Configuring QOS for all types of Environments like BGP with MPLS, other etc., Protocols.Recommendation needed for a "QOS Book" - Study Material based on above requirement.Best R...

Dear We have 1721 router.Today router restart automatically two times.I checked on router there is no log. can you tell what is the reason?Thanks in Aedvance

Can anybody reply me with disadvantages of Bridged-Network in Frame-Relay scenario with good documentatiom.If someone can provide me documetation and advantages of implmenting EIGRP replacing Bridged-Network in Frame-Relay, Will be of great use!!!!Th...

Any time I try to save the running config to NVRAM, I get an error saying NVRAM Verification failed. The config registar is 0X2102. Any ideas?