Routing

Hi,I have put several question on forum. i have recived we positive response. My question is How I eras Flash of As5300. I want upload IOS but flash space error comes in tha way. Thanks.

I'm sure I've seen this on the Forum before, but could not find it. I'm trying to implement a load-balanced connection to Sprint ISP. I plan to use GLPB on the Ethernet side but does anyone have a caned script to tweak BGP to load balance across to...

Hello,How to clear the routes learned via EIGRP routing protocol?.In the attached diagram, At my HQ L3-Switch, When I see the show ip route 10.22.0.0 , it displays that it learned from 128 KBPS link Router. I'm going to shut the 128 KBPS link ethern...

Hi,I was planning to use the HWIC-1GE-SFP on my 2811 as a 3rd FE/GE port for L3 connectivity and dynamic routing/EIGRP. Would you know whether this will work. Cisco TAC says they are still researching this, so now answer thereThanks, Sujohn

Issue discovered while stress testing two T1s. T1s test clean h-2-h when cable removed from VWIC-2MFT-T1 (T1 (2 port) Multi-Flex Trunk WAN daughter card), but can not run 1n8 test pattern to CSU loop. Tried this with two different cards with same res...

Hi all, need a little help !As per attached diagram, I have configured 'reliable static routing' to route between two different ISP'S and internet connections. This gives the user some resillience when connecting to a remote server (AS400).The proble...

HI all,Here is a question about the behaviour of an Alcatel Voice Switchboard (Alcatel Omnipcx enterprise with ACT technology and OXE over ABCF network).The thing is that this Switchboard has two connections to two 3750 Cisco Swiches (working in stac...

Good day,I'm looking for all exam ( ccna , ccnp etc..), i have done. this week, i make composite exam but the result is not available.Can i see exam state fail or success) in site cisco ?? Where ??Regards.

Hi,Any one with good concept of split horizon..1.Does Split Horizon applies to all the protocols (Link State/ distance vector & BGP)...2. RIP : As rule says, The router will not advertise the same route/prefix to the router from which it learned the ...

Hi,Wanted to ask some details about the IP Options field in the IP header of the packet.Scenario:Suppose a router is configured such that it edits the IP options field of the packed in the IP header(adds some information). What do the other routers ...

i need to find the ip address of the pc from which mails are being sent to my mail id. for testing purpose i have sent mail to my own id.By seeing full headers of my recieved mail, I have the access to my router, by using show ip nat tranlsations, i ...

Hi guys, I'm running into a problem trying to setup authentication in RIP.First of all, I've successfully setup RIP between 2 routers using multicast (RIP v2) and key-chain.Now, when I've changed the config from multicast to unicast, using the neighb...

hi all,i got some help a week or so ago on how to get a back-up internet site working with bgp. as far as the wan goes, i understand how to tell everyone that the backup site is to be used if the main link goes down. next question:Set up and follow...

Hi there,I'm attempting to strip tac from a remote 2848G switch. I removed some config from another switch and effectively locked myself out. I'm assuming there's an order of removing the config that has to be followed. Here's what I have:set tacacs ...

Config-register is set to 0x2102.when I pull the PCMCIA out and reload the router, it come up in boot mode.This is really bad and I would prefer it boot into rommon> and loos all functinality. rather that have some features but not others.Is there a ...