Routing

Hi all, I have a routing problem. I can ping Lan2 from Router1, and I can ping Lan1 from Router2. Also I can ping the Serial side of Router1 from Lan2, and the Serial side of Router2 from Lan1. However I cannot ping LAN to LAN, and I cannot ping the ...

Sorry for OT, has any body try to use PIX for client-to-site VPN connect, which users will be authen by ACE secure token? Here I would like to ask the following: 1) Can PIX connect to ACE Server directly without the use of Radius? 2) If yes, can this...

We have three facilities. Two of whitch are connected directly to each via DS3. We are working to provision a 2nd DS3 that will connect to the same two facilitied to each. However the 2nd DS3 will be using seperate routes and will also be going throu...

Hi , I have Cisco 1721 router with two Wic1-ADSL cards, I wanna setup an internet connection over two ADSL lines. However, I want that router must automatically balance the total bandwidth, in other words router should balance all traffic on these tw...

Two C2610 connected via Serial V.35 cables. R2 router S0/0 IP = 10.0.0.2R3 router S0/0 IP = 10.0.0.3 (DCE)On both routers, int s0/0 displayss0/0 is up, line protocol is up.However, I ping the IP addresses locally and ping is unsuccessful. What am I m...

I like to upgrade to 12.2 release from 11.3. However, this fails and the system says not enough memory. threre is 65536K/4096K bytes of memory which should ebe enough.Question: Does the boot rom have to follow the IOS releaseIOS (tm) 4500 Software (C...

Hello,I am facing some problem with our network, it seems like there is some routing loop.When I traceroute from my PC(10.51.40.12) to our remote location switch(10.50.8.250) I am getting the follwing output:C:\>tracert 10.50.8.250Tracing route to 10...

Hi all,i've a problem with my RPM:It keeps on giving this message:00:01:16: %RPM_VIRTUAL_PORT-3-VRTLINFO: Starting bulk updates ...00:01:16: %RPM_VIRTUAL_PORT-3-VRTLINFO: ... Completed Bulk updates00:01:45: %RPM_VIRTUAL_PORT-3-VRTLINFO: RSCPRTN_RESYN...

Hi all I have 2 depts distance is around 500 mts, rt now we are using "Pairgain" over 2 pair copper( 4 wire, ordinary telephone cable)its actually HDSL.but now a days pairgain is not available so i'm planning to replace all these pairgain systems usi...

I have just loaded a new image into flash on our 3745 and have left the old image there also. What command(s) would I use to load the new imageboot system flash c3745-ipvoice-mz.124-2.T1.bin???Or do I need a : after the flash or am I completely inco...

Hi all.I will shortly be getting an 857/877 ADSL router and have a few questions regarding the setup with my infrastructure.I have 10 static IP's from my ISP. 1 is for the WAN on the ADSL router, 1 is used for the external I/F of my Checkpoint. I hav...

I've got 2x Cisco 4500 routers in my lab.They are based on identical HW, and I've decided to upgrade the IOS.The first box went very well, where for the second one something didn't work.Now when I boot it up goes directly into rommon.I found a docume...

Hi there. We have a 837 router, one of the older ones that has 32MB of fixed RAM, and an addtional 16 MB in the slot.I see that the upgrades to 12.4 require a minimum of 64MB RAM - which the new 837's have. What can I do with this 837? I cannot se...

We are having intermittent problems across our WAN, and have been unable to determine what is causing it. - There are two networks involved; Net A - 10.1.3.0/24 and Net B - 10.1.2.0/24 and 200.200.29.0/24.- There are two Cisco 1720 routers which rou...

Dear All,what are the main differences between L3 switch and router? can we replace a router with L3 switch as its router module supports routing ????? in ospf network can L3 switch elected as DR r BDR ???? can anybody clear me PlsThanks in advanceRe...