This is how I do it on ASAobject network L2L_NAT_OVERLOAD_IP host 10.200.255.1object network L2L_NAT_DST subnet 172.1.1.0 255.255.255.0nat (INSIDE, OUTSIDE) source dynamic LAN_INTERNAL L2L_NAT_OVERLOAD_IP destination static L2L_NAT_DST L2L_NAT_DST th...
Forum Posts
i can't ping from Admin to R1 or R2 or any of the endpoints connected to R1 but i am able to ping R3 from admin and then am able to ping the endpoints of R1 from the cli of R3 any ideas on what the issue is
Resolved! How is MPLS TE path weight calculated?
I'm trying to figure out how a TE Tunnel on Cisco IOS-XE gets its path weight value.R1#sh mpls traffic-eng tun tu100 Name: R1_t100 (Tunnel100) Destination: 3.3.3.3 Status: Admin: up Oper: up Path: valid ...
Whats up Cisco forum users, So i am experiencing something weird, basically when i mention the explicit-path in the segmented routed Tunnel (with the command 'path-option 10 explicit name path1 segment-routing' , for example) the Tunnel does not work...
Hi!I'm trying to opload a config file with txt extension to a ISR4321/K9 and router TFTP debug "TFTP: Sending error 2 Access denied". Is this is possible? 001392: Mar 4 10:09:22: TFTP: Server request for port 54576, socket_id 0x7FA143143B30 for proce...
Hi All, Currently entire network is under ospf area 0 with internet traffic in DC routed out to ISP 1, and DR internet traffic routed out to ISP2. We have a requirement to do a routing failover from DC to DR when Internet connectivity to ISP1 is down...
Hello, In out subnetwork we are using many internet lines and accessing these inernet lines reachability is controlled via cisco mac access-list which is configured and applied on the C3750 switch.everything was working perfectly with no prob...
I try to repost here one of my posts that found little response ... I need to extend some VLANs between two location (the Enterprise DataCenter and a remote DR DataCenter).The obvious solution is using OTV between two CSR1000v's.The connection I have...
Dear the Cisco Networking Community, I have just read the document: https://www.cisco.com/c/en/us/support/docs/ip/open-shortest-path-first-ospf/47862-ospfdb3.htmlI noticed that in Router 1.1.1.1, there is an entry 5.0.0.2/32 via 5.0.0.2. I am pretty ...
So if you want to reduce how much bandwidth can be used from certain hosts/subnets destined to one particular subnet, it would be best configure Layer 3 QOS correct?If let's say VRFs on a L2/3 switch are used for just the particular source subnets, d...
Resolved! Multiple BGP instances on n9k
Hello,In a lab setup, I want to set up 2 bgp instances in 2 vrfs to test eBGP feature among those 2 instances.I have one n9k is this possible to set up.How would I leak routes between 2 vrfs? Is it possible to have 2 AS numbers on the same n9k or do ...
Good afternoon allI would like to know if it is possible to use a Mobile 4G modem as a backup of my main link,on the ISR4331 router. For connection USB PORT
i have a cisco asa 5505 and i am controlling it with ASDM. Is there any possibilities to find the connected device's mac add? Becuase, i wanna find and block this user, he or she has a huge network crash while working. thanks for your nice and gently...
Hi all, I am doing some self-paced studying on EVE-NG but stuck on few things.I was wondering if anyone can help. ISP router IP: 172.16.5.21 My currently setupISP > Cisco Router > FW > 2 zones > 1 PC in each zone (Inside/DMZ) Cisco Router has 2 IP-...
Hi,I need to redirect show tech-support output to a tftp server on a Cisco 7609 chassis for that I used the following command:# show tech-support | redirect tftp://IP@/file.txtBut when I consult the tftp server I don't find the complete output of the...
