Looking for clarification and understanding of the cli command: show ip bgp version recent # Example:show ip bgp sum | i tableBGP table version is 5000, main routing table version is 5000 show ip bgpSeveral hundred prefixes are shown show ip bgp v...
Forum Posts
Hi, I have a setup where x3 routers are connected to a core of x2 stacked Huawei chassis switches. For redundancy & to fully utilise all x3 routers I want to use GLBP, however it doesn't seem to be working correctly. Setup is extremely simple, on eac...
Resolved! Cant ping GRE destination
Hello All,i start a new lab with tunnels i set up everything(EIGRP + Tunnel0) but i cant ping from R1 to R2 GRE ip dest.i set up eigrp and one loopback for every router.R1 config : interface Loopback1ip address 1.1.1.1 255.255.255.0!interface Tunnel0...
Hi there,I have to design a system using OSPF to communicate different mobile points (camions set). These nodes, only will use internet to mount tunnels between them through a 4g / inalambric system (they are communicate only with them). Idea is to u...
Hi,I have the problem when I send the sms with write "survey".I following the guide linked here https://www.cisco.com/c/dam/en/us/td/docs/routers/access/interfaces/software/deployment/guide/guide_isr_lte_sms.pdffor know the status of the router or on...
How do i set the hardware clock? the calendar options are missing from this release. The only settings I see are ISR#clock ?set Set the time and dateISR#clock
Hi all, I am trying to use Route map to filter multiple ACLs in one hit and applying them to an interface.Is there a way to this using routemaps? So basically ACLs below: ip access-list extended SSH_WebAppspermit tcp 13.50.60.0 0 0.0.0.255 host 192....
Hello guys! I have trouble to connect my L3 switch outside internet and I can not understand where is my wrong.Please see my config for switch L3 and router.Thank you in advance . L3Gateway of last resort is 172.16.2.0 to network 0.0.0.0C 192.168.1...
A "show ip pim int" command shows multicast switching as "fast". Can we have it use CEF to reduce the load on our router? RTR2(config-if)#do sh ip pim int et0/0 detailEthernet0/0 is up, line protocol is upInternet address is 192.168.0.2/24Multicast s...
Dear all i need support and opinion for my attached 3 files for my isr router 2911 and 2 switches ws-c2960x-24ps-li need to know if its fine ? or need to add some command lines or any modification please share to apply it on my devices many thanks...
I upgraded an ASR1006 using ISSU and followed this documentation. https://www.cisco.com/c/en/us/td/docs/routers/asr1000/configuration/guide/chassis/xe-16-6/asr1000-software-config-guide-16-6/issu-asr.html#con_1145249 Everything is going smoothly unti...
Attached lab. Im a beginner, practising RIP configuration. all the routers are pinging each other, but the end device not able to reach other network.kindly help
hi, engineers, I have a problem with router 1841 when resetting the router just I type config reg 0x2142 and the second comm reset and power of and on again after that as you see in the pic
Resolved! Help with GRE
Hello, Sorry if this isn't the correct spot to post this, I'm new here and new to networking.I'm trying to set up a GRE tunnel from my Edge to New Branch routers. I keep getting the following error:New_Branch(config-if)# %ADJ-5-PARENT: Midchain pare...
Just wondering if a PIM neighborship is required for the two PIM routers to process auto-RP packets.
