Hello, I want to install RV325 to use dual wan with Bell home hub 3000, I plan to use Bell home hub 3000 like DHCP server and wifi, and use RV 325 like a switch. Bell Hub has 192.168.2.1 ip adress 192.168.2.1 I tried to install RV325, changed ip to 1...
Forum Posts
I have a Cisco Catalyst 3560-CX switch and an RV320 router.I am trying to configure my router only for VPN and the switch in layer 3, I have 3 Vlan: Vlan 2 (wireless data), vlan 3 (VoIP server) and Vlan 4 (NAS and web server), but I still can't ping ...
Resolved! OSPF Multi area route inefficiency
Hi,In a multi area like this where if we have a direct link from R5 to R7 and R6, we will have a shorter faster path to those routers, how should we fit it in with ospf protocol definition?I can't come up with any solution other than merging area 1 a...
I having problems to make a route static with packet tracerI have these:Router1:ISC(config)#ip route 192.168.3.32 255.255.255.224 192.168.3.30Router2:LA(config)#ip route 192.3.0.0 255.255.255.128 192.168.3.1LA(config)#ip route 192.3.0.128 255.255.255...
Hello floks,In my setup, i use Mgmt-vrf for system management. When the management interface gets dieconnected, the global vrf should be used. The config is as below. Switch-3850#sh run vrf vrf definition Mgmt-vrf!address-family ipv4route-replicate f...
Hello. I have a home test environment that I would like to see if I can get internet access.I am using a Cisco 2901 Router and an unmanaged Netgear switch.I would like to see if I can get internet access to the device connected to the unmanaged switc...
Resolved! OSPF Best Practice for Keep Alive timers
Hello, If I use Nexus 6ks and 5ks with 2k FEX, and SFP-10G x2 Port-channels, how should I find out how much bandwidth I am gonna lose from my links for hello intervals? and how low I can go for hello intervals for the fastest convergence? thanks
Resolved! Multi-Level Priority Queue QOS
I am doing a QOS config in the following scenario.I have a 250mbps MPLS circuit, where voice and data will both be passing. I know there are multiple ways to do this, just wanting some peer review on the plan below and see if I may be missing anythin...
I've got a one problem. Me and my friend have the same ISP. I checked my External IP address at WhatIsMyIp.com and my friend do it to. And we saw we have the same External IP.So my question is can 2 routers have the same External IP address?If i'm ri...
Resolved! CCNP exam & New exam
Morning from London, I'm not entirely sure where to post this, so correct me if I've posted in the wrong place. I'm thinking about starting my CCNP studies. I bought the 3 books while studying for my CCNA, however, the exams are changing in Feburary...
Resolved! BGP question
hi, I have been trying to find the right spot that indicates some light to my question, but if you think Im not understanding correctly, please do let me know My understanding for local preference is that is the second best path in the equation on ho...
Hello Please find topology below (AS100) R1( 10.0.0.1/24)-----Switch1------(10.0.0.2/24) R2( AS 200) | R3 (10.0.0.3/24) (AS300) R1 is ebgp neigbhor...
Hi all, I am facing issue with FTTH pppoe connectivity, i have two connectivty with my location.The primary link is BSNL leased line and secondary link is FTTH pppoe with bridge mode.I have created ipsec site to site vpn to reaching to my DC, i am no...
Hi friends,We use main gateway fortigate 100e on our company. We have buy a SG300-10SFP layer 3 switch. I configured vlans and ip address on cisco switch.VLAN 10 - 10.42.10.1VLAN 11 - 10.42.11.1VLAN 12 - 10.42.12.1 GE10 interface trunk mode, admit al...
Hi All, Recently our users started reporting that their internet connectivity is extremely slow . We have a 20 Meg connection and straight away when we checked couple of things like bandwidth utilization it is well under normal but still they have sl...
