Hello all, I have a bit of a problem that I hope some of you can help me fix.I have two Cisco EPC3928s Router/Modem units. One is my primary connection from the ISP to my PC and my Wirelesses router. Also I use built in DHCP service on it. I recently...
Forum Posts
What is the exact command to find the received routes in BGP ? need to check only the recieved routes in my router.(running BGP)
Resolved! OTV problem between my 2 sites
Hello,I'm trying to use OTV to extend my vlan 101C3850West Gi1/1/2 <-> Gi0/0/1 ASRWest Gi0/0/0.900 <-> ISP <-> Gi0/0/0.900 ASREast Gi0/0/1 <-> Gi2/0/24 C3850East On both C3850 I created an interface vlan101West----interface Vlan101ip address 10.216.1...
Hello Experts, I am going to create an interface in L3 switch as below. My question is that in the syntax there is no command as no shutdown. Will the interface will be up as per the below without the no shutdown command. interface TenGigabitEthernet...
Does the ISR4431 router support IPSEC configuration?Do I need a license for such a configuration? Router: ISR4431 / K9Version: 03.13.04.S
Resolved! ACL direction on sub interface
Forgive me for this as I'm sure it's been asked umpteen times but I just need to clarify it in my head with the example below.I want to permit User A access to Web Server A but don't want to place an ACL on the User A router but rather in a single pl...
Hello community, I am struggling to get Inter-VLAN-Routing running on a WS-C2960L-48PS-LL, Version 15.2(7)E0a.For testing-purposes I created two SVIs with IP-addresses, 2 VLANs and enabled "ip routing". I followed this guide provided by cisco:https:/...
I reserved the Multi-IOS Cisco Test Network Lab for the weekend and then when I logged it the error below popped up with an error of Failed to license simulation. Then I uploaded my own lab and I got the error below. Failed to launch GRE Tunnel.virl(...
Whether IS-IS graceful restart and IS-IS BFD can be enabled simultaneously in the N/W. If yes what are the Advantages and Disadvantages.
here's my NTP config on my 2921 router. i'm just a client syncing its clock with pool.ntp.orgntp source GigabitEthernet0/1ntp peer pool.ntp.org prefer so, some white hats at my parent company scan my router and tell me that the NTP service is running...
Resolved! QoS for traffic
We've recently setup a RDS environment and would like to do a basic QoS rule to prioritize rdp traffic, but I'm not sure the best way to do this. We have a 100Mpbs fiber connection (soon to be 250) and our setup is like this ISP->WAN router->WAN Swit...
Hello Cisco team, I have a Cisco 881 Router and it is assigning an IP: 10.64.36.116 to a Cisco IP Phone. I dont want this IP to be assigned to be any device. I have written a command on the Router: ip dhcp excluded-address 10.64.36.116 but still the ...
Whether IS-IS graceful restart and IS-IS BFD can be enabled simultaneously in the N/W. If yes what are the advantages and disadvantages
How do you properly size Performance License and or not one with the Cisco ISR 4000 Series routers? For example, say I have an ISR 4221, which can do 35Mbps to 75 Mbps. Now with the default License, you can only do 35Mbps. So, does that mean if I hav...
Resolved! IP Phone and PC on ISR 4431 port
hey there community, I would appreciate your thoughts and ideas. I have "little" problem in my UC environment. At locations I have one ISR4431 with IP phone on one of the GI ports, phone is registered and working properly, but now I got task, to add...
