Let's say you have one network 192.168.10.0 in one location and another 192.168.10.0 in another location. See attached lab drawing (disregard the 172. and pretend it is 192.). Just how would you configure the ASAs to allow SSH from hosts on the left ...
Forum Posts
Hi, Im kind of new to this and im trying to do my best, I made the the two network setup and everything is fine. Configured the VLANS , trunk and access ports and the router on a stick. However I'e tried many routing methods in order to connect both ...
Resolved! EIGRP neighbor flapping
I have configured neighborship between ASA and Router through Switch. EIGRP keeps flapping every 120 seconds.ASA(inside,192.168.10.2) -------(gi1/0/5)SW1(gi1/0/6)-----(GigabitEthernet0/1.10 192.168.10.1 )2911 router ASA Side configurationinterface G...
Hi, I need to add CUBE to a customers 4431-K9 Voice Gateway. I'll add the UC iOS and the CUBE licenses. But for the latter I noticed something new (?). See below figure. The 'CLASSIC CUBE OPTIONS' tab also exists and contains the 'classic' CUBE lice...
I have 4 sites on an mpls network and 3 of the sites are congesting the main site wan circuit (mpls). All sites only have 5meg circuits for site to site only traffic so it's not hard to congest but one of the offices is using the main site circuit t...
Hi, I'm trying to connect a basic comcast modem only (not modem/router combo) to my 2921 router and have it give internet access to my lab. Any help is greatly appreciated! Here is my current setup and topologyInternet- assigned via dhcp from ComastN...
My Configuration is below I'm able to ping websites inside the router. But unable to browse the internet on Lan IP address. Building configuration...Current configuration: 2680 bytes!! Last configuration change at 11:59:53 UTC Sun Mar 24 2019! NVRAM ...
Resolved! Route Map
Hello everyone,I have a question .My ASA 5515 is placed in a full meshed MPLS network.This ASA which has the IP address of the MLS router as default route has several vlan configured. Soon an Internet connection will be installed to which only one of...
I have setup a DMVPN network over a ISP MPLS network. And I have conduct file transfer test from one end to the other end though the DMVPN network, and find that the thoughput is 80% of the link bandwidth (e.g the link bandwidth is 10Mbps but the act...
I need a outdoor cable for the ANT-3-4G2G1-O. The 4G-CAB-LMR240-50= is of type Plenum but I need outdoor. Anyone that has come across this ?
Hello, I'm receiving these messages from the RV340 log, could you please tell me what does that means?<warning>kernel: [4289114.860256] <4>[WARN] [AV] DECOMP ERROR 129 <warning>kernel: [4305498.769273] <4>[WARN] [AV] DECOMP ERROR 133 That code betwee...
Resolved! Cisco 4431 using wrong route
I have a Cisco 4431 that was reloaded at the weekend, config saved and confirmed the same as before. It has two WAN interfaces.WAN 1 with the default route pointing to itWAN 2 with higher cost default route pointing to it. Before the weekend it was w...
I am looking to build a home lab for CCNA. My company will pay for the equipment If I can find a list directly from Cisco that names the equipment per lab or a third party that Cisco redirects to. Does anyone have any information or links they can sh...
Hello,I've got an issue between two endpoints across our wan. I setup spanning on two switches and and found some TCP resets and in the capture it shows the source IP of the reset the other end point in connection. However the TTL was 254 so it wasn'...
I believed I had properly accounted for the IPSEC/mGRE overhead on my Tunnel interface settings (IP MTU and MSS), but was experience high CPU utilization (IP Input) due to fragmentation and reassembly.Below are the overhead calculations I used origin...
