Hello team Last day i upgraded all controller in to 20.3.5 -> 20.6.5 version as you know in 20.3.5 which use multitenant mode , the vsmart are bind in each tenant. but when i upgarde it 20.6.5 version. the vsmart are come out side. I want to use th...
Hi guys,My company has branches in 3 locations (the US, China, and Canada). I want to create a FULL-TUNNEL VPN for users who connect from coffee shops, airports, and hotels.I will do it using the Cisco profile editor and call it a UNSECURED VPN profi...
In my environment we have multiple cEdge devices, 1 vManage, 2 vBond and 2 vSmart.Due to some reasons one of the cEdge devices lost connectivity to vMange. Not sure of the exact reason.But would like to understand, will there be any impact due to thi...
Wanted to understand the best practices when updating the prefix-list & data prefix list in SD-WAN network.For example I have the below prefix-listlist_abc: 10.10.10.0/24This prefix list has been used in Centralized policy.I wanted to added new subne...
Hello Team,Please help me to understand: in hybrid scenario of Controller deployment, if vBond resides behind the NAT, and lets say cEdge on-boarding is done with the Internet as TLOC then as we know, vBond should learn both the Private and NATed pub...
Hi Guys, Can somebody help to identify what might be the problem here? I'm trying to redistribute NAT DIA into BGP but it's not working. Please see screenshot below. It only worked as expected after I put network 0.0.0.0 statement on bgp.
While doing Cisco SDWAN cEdge routers configurations, we are unable to configure IPV4 address. We can only option of IPv6 address. Need help to configure IPV4 address. Thanks sdwaninterface GigabitEthernet0/0/0ip address 172.21.26.10 255.255.255.252 ...
Hello, team. Good day. We are planning to upgrade below platforms to 20.9.x. Is there any upgrade path ? - vEdge 5000 20.3.3 - vEdge 2000 20.6.3 - ISR1100-6G (Viptela OS) 20.6.3 Thanks.
Hello , We would run dual stack (IPv4 & IPv6) at service side, and also we would run dual stack (IPv4 & IPv6) on the transport internet interface(underlay), on SD-WAN router. Is it possible to enable IPv4DIA (NAT44) and IPv6 DIA (NAT66) via the same...
Good morning all!I am working on a project on our SD-WAN. I am new to SDWAN and vManage and was asked to look into possibly scripting some packet captures over a period of time. Our SDWAN consists of several IR1101's and they can only be managed via ...
In my environment I have 2 vSmart controllers. (vSmart-1, vSmart-2)In cEdge-1, the OMP peer is established only with vSmart-1. No details about peering with vSmart-2.in cEdge-2. the OMP peer is established with vSmart-1, for vSmart-2, the status is i...
We have OMP route exchanged & we can see to & from packet but websites are not working which goes through proxy server over one public color where as with other public color its working
Hi, I have to pass the serial to the tac, use this command in vManage, is this the correct information or does anyone remember which command by cli, catalyst manager or both I can collect this information. Thank you very much for your help Regards....
We have a Cisco hosted SD-WAN fabric in a shared environment meaning we are a tenant that uses shared control components. There is a c8000v hosted in AWS that we onboarded and has active control connections to vBond and vManage. For some reason I'm n...
Can we use same IP Address for Sysem IP and VPN 0 of a vBond and vSmart
