Hi Team, Default, SDWAN devices use DTLS to encryt packet (vedge, vmanage, vmart, vbond). So if I use DTLS, TLS can be disabled or TLS still available ? And i wonder that are there any way to disable TLS if i want ?Thank you in advance !
Forum Posts
Resolved! SD WAN HUB&SPOKE TOPOLOGY
Hiiiii team....Can someone help me with this? We have a client who wants to go to SD WAN, but doesn't like the idea of changing ISR4K to C8200... so they are deciding to use their upgraded ISR4K, however, all their branches (about 200 or more) have o...
Resolved! Edge is in good status
.Hello, Why 6 Edge is up and it also shows "Partial" with yellow? Please see the below. Is this normal? ThanksIs this relative with "connet"? Please see the below
I have vManage's cluster with Enterprise certificate, and I want to know is it possible to backup certificates from vManage's? for example, if I want to deploy new vmanage and I would like to reuse certificates from old vmanage (csr request and cer f...
Resolved! vManage size is bigger and bigger
Hi vManage and vbond/vsmart are installed in eve-ng/linux base, which is installed on ESXi. Their size(vManage 2.9G) in eve-ng is less than 4GB including some other routers. but the size is becoming bigger and bigger after installation and run. The ...
Hi Please see the below. The device below is one of the vEdges. but why this one does not show vSmart connection? Thank you
Hi All. I have Cisco SDWAN running well using Control Connection on DTLS. For some reason, our customer asked to change the control connection to TLS. Can someone please share document related to pro-cons for control connection using dtls / tls on Ci...
SD-WAN how to move the vpn 512 eth0 interface to vpn 0interface vpn 0 interface system af-type ipv4ip-address 100.1.1.114/32if-admin-status Upif-oper-status Upif-tracker-status NAinterface vpn 512 interface eth0 af-type ipv4if-admin-status Upif-oper-...
Looking for some more details on the weight command in relation to TLOCs. Documentation says the command allows configuration of 1 - 255. Is it correct to say - Primary Link Weight 1 Secondary Link Weight 255 So, for every 1 flow on the primary, 255 ...
Hi Experts, My SDWAN system run on-prem, I added Serial file of edge devices to vManage already and they authenticate and join overlay well, But vManage alway alarm: Devices have no license assocated. (Devices added to smart account already)Are there...
As per above picture, telco gateway router replies ICMP type 3 Code 4 message to the cEdge router patternly, when cEdge trying to send UDP packet of >1500 length to vSmart. My question is 1. Do I have to remove DF bit with "clear-dont-fragment" comma...
Is support provided now for encrypted NTP and DNS in cEdge code? I don't see anything in the configuration guides about this.
Hi All,I am very new to SD-WAN , I want to know can the SD-WAN devices we might be going to use have facility of bandwidth management like we have in Bluecoat Packetshaper, as we are looking for all possible options of SD-WAN service ProvidersIt'll b...
I am using vManage on VMWare and all other devices on EVE.I am able to add 1 vSmart, When I am adding the Second vSmart it throughs me below error.Failed to add device Device with UUID f164340b-e28e-4bdc-b46e-d0c800acfcb0 already exists SDWANKinly he...
Hi,I onboarded a couple of edge routers and some of them have not installed root-certificate and control connections are not there for Vsamrt vEdge20# show control connections-historyLegend for ErrorsACSRREJ - Challenge rejected by peer. NOVMCFG - No...
