Buy or Renew
Buy or Renew

Server Networking

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Cisco UCS X-Series Energy Efficiency Offer

 

Forum Posts

Start a conversation

1000v promiscuous veth port groups

I have setup a promiscuous VETH port group on a 1000v. I have found it works, as in the veth port group can ping all VM's in the secondary community and isolated vLans.My problem is that Cisco is saying this is NOT supported. They state that the only...

Resolved! Nexus 1000v 4.2.1 - Interface Ethernet3/5 has been quarantined due to Cmd Failure

Hello,i get the error message "Interface Ethernet3/5 has been quarantined due to Cmd Failure" when i try to activate the System Uplink ports on the Nexus 1000v VSM. The symptom occurs under 4.2.1.SV1.4 (has been fresh setup, did before tests with 4.0...

schlemmer by • Level 1
  • 4303 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Nexus 5Ks back to back

Can the Nexus 5Ks be daisy-chained to extend the FCoE fabric?The setup:Blade chassis with pass through modules (pass throughs do absolutely no switching, just present a CNA to each Nexus 5K port at the ToR).Can that N5K at the ToR be connected to ano...

visitor68 by • Level 5
  • 745 Views
  • 2 replies
  • 0 Helpful votes

Resolved! N5k Peer keepalive path

Hi all,A simple setup, 2 x Nexus 5548 connected by the peer link, 2 x 6500 in VSS. Each 5548 has two 10G uplinks to each of the 6500 in VSS.My understanding is that the peer keep-alive should not be carried over a vlan that is allowed on the peer lin...

Resolved! N5k, vPC consistency check

hi all,I got a pair of 5548, vPC works great. However the vPC consistency check show the two switch configs are different! I don't know why vPC still works fine. See the below output of the show vpc consistency-parameters global command. it's weird t...

1000v uplink to Catalyst 4500

We have a 1000v switch uplinked to nexus 5K and Catalyst 4500 switches. I can see all the VEMs(ESX servers) connected to the nexus 5K uplink switch and everything seems working fine. However, I am not able to see the VEMs uplinked to Cisco Catalyst 4...

FCoE Uplink Bandwidth

Folks:Let's say the scenario is a blade chassis with four (4) 10G CEE uplinks to a ToR FCF....(maybe even a UCS - doesnt matter).In  such a converged network environment at the server edge, how does one  determine how much uplink bandwidth to dedicat...

visitor68 by • Level 5
  • 1275 Views
  • 4 replies
  • 0 Helpful votes

Resolved! Cisco Supported Architecture for FCoE

Do these two architectures support FCoE from the server all the way to the N5K??FirstAn IBM chassis with a Nexus 4000 FCoE pass-through blade switch uplinked to a Nexus 2232 top-of-rack switch, and then uplinked to a Nexus 5020 end-of-row switch, whe...

visitor68 by • Level 5
  • 2943 Views
  • 8 replies
  • 0 Helpful votes

Configure priority flow control

Hi,I am trying to configure priority flow control  on a Nexus 5020 (IOS 4.1(3)N1(1)). I have enabled it on the relevant  ports and am trying to enable priority flow control for traffic with cos  values 2 and 4. My configuration looks as below (output...

vbhanu123 by • Level 1
  • 630 Views
  • 0 replies
  • 0 Helpful votes

Resolved! Nexus 1000v ERSPAN

Greeting GentsI`m actually designing an implementation for nexus 1000v and i`d like to know if i can dedicate a port for ERSPAN traffic (inter and intra VMs) and how it`s doneIn doc from cisco they state the following after setting up the port-profil...

Load more
Unanswered Topics
View All
Top Solution Authors
View All

Review Cisco Networking for a $25 gift card