Server Networking

Hello all,I tried to do a password recovery on a n7k-sup2 and can't seem to login.  I issued a write erase in the switch(boot) mode and reloaded.  I'm lookinga at the cisco manuals online but can't seem to find anything on the default password.  All ...

In Nexus 7010Hi Team, In N7010 when i checked the environment status i can see minimum thresold is set to 105 celsius but it documents its mentioned the operation temperature is 0 to 40 celsius. In sh environ temp output i can see the below sensor is...

Hi,I have installed 2 x cisco nexus 7009 at two seperate datacenter location with the same building. As I am configuing the vPC, I would need to link up the 2 x nexus 7009. However, when I linked up the 2 x nexus 7009 via the 10g port, the port is al...

Can below two line cards configure into same VDCN7K-M148GT-11LN7K-F312FQ-25 We are using SUP 2 with NX-OS 6.2 Thanks

Dear Geeks,I need to provide a solution where I have to connect an HP c7000 BladeSystem Chasis to a Nexus 5k or 2k switch with 40G connectivity.? Will a simple Etherchannel work on both ends ? What module will I need to put in the Nexus or Bladesyste...

Hican i configure the switchport in nexus 2k as trunk port..(Not the ports connected to Nexus 5k but the ports which we use for server termination)..The requirement is the switchport will be connected to VM server which supports trunking and passes m...

We have a situation, the oracle exadata database server is unable to ping the default gateway when using LACP (between server and N5k) and otherwise (without LACP between server and N5k) the communication works perfectly fine. the set-up is like belo...

HelloA simple network configured by some one else and my role is to trouble shoot . one 5k or 5k1 is connected with two different server (one side Hp and second side emc- multiple blades) then there was no issue , everything was fine , when we connec...

Hi AllI have a requirement to upgrading our UCS 5108 firmware, and I would like to know if there's any gotchas that I should watch out for. since the firmware will be jump upgrading from 2.2(1b) to latest firmware 3.2(2d) we've a couple of UCS 5108 c...

Folks,           The issue is that in a Nexus 5000 switch, when I do a write erase, it does not bring the switch to the default state. I have been manually removing snmp and AAA commands and then doing wr erasr to bring the switch to the factory defa...

Hello Cisco,It seems i cannot disable the sending of DTP packets on a FEX port:Switch(config-if)# switchport ?  <CR>           access       Set access mode characteristics of the interface  autostate    Include or exclude this port from vlan link up ...

I am attempting to install APIC-EM 1.5 on VMWARE that meets all necessary hardware requirements but after I configure the network settings on the APIC and it verifies the settings I get a bunch of java errors and the installations fails to continue.

hello friends, when i configure vlan in switch 4506 there are a error is there  "error exiting config-vlan mode 33 :attempt to change state of a default vlan " please help me to solve this error...

Dear Expert,My customer has N7K SUP1 with HA as below and I need to replace 2  with SUP2E 6.1.2 from SUP1(6.1.1).As per Cisco document, it is required EPLD upgrade from SUP1 to SUP2E with Fabric-2 module, but there is no estimated time for EPLD proce...

N7K A and N7K B has single Sup module, N7KB VPC role is secondary .N7KA vac role is primary ( as per the Role Priority and Preempt not configured). Need to replace the Sup module  at N7K A without any down time.   Please suggest the Process.  Note : ...