Buy or Renew
Buy or Renew

Server Networking

cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

Cisco UCS X-Series Energy Efficiency Offer

 

Forum Posts

Start a conversation

Resolved! connect C-series server to FI

Hi Alldoes I need any kind of license to direct connect Cisco C-series to FIas I found license for connecting C-ser to FI and If not required so what is the purpose of this license?UCS-L-6200-10G-C         UCS 6200 Series Only Fabric Int 1Port 1/10GE...

Amr Hafez by • Level 3
  • 1808 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Nexus1000V Multicast question

Hello,My customer says that vmware has a maximum of 256 multicast groups and 10 sources per switch.https://pubs.vmware.com/vsphere-60/index.jsp?topic=%2Fcom.vmware.vsphere.networking.doc%2FGUID-97724211-5167-428F-A217-871963A7DFF7.html What are the m...

lquerol by • Cisco Employee
  • 1134 Views
  • 4 replies
  • 0 Helpful votes

QoS statistics on N3K

Hi,Is there any (hidden) command to check per-queue statistics on Nexus 3048T? Something like "show policy-map interface" on Cisco routers. This command run on N3K shows only configuration. How can I verify how much traffic is passed or dropped in sp...

Resolved! Vmotion issue when using vPC

i have an issue when running a 40 gig port- channel using Vpc between a pair of 5596s to esx 5.5 hosts. We can get lacp running properly where I can see on a sh port-chan summary that all 4 connections (2 on one, 2 on the other) are all properly bund...

connect FI with fc port and zoning

HiI know that FI can work as SAN SW so:I have UCS blade (virtualized with ESXi) and fabric interconnect in FC switch mode that connected to Netapp FAS and I need to connect Symantec netbackup appliance using FI in FC switch mode then I need to config...

Amr Hafez by • Level 3
  • 787 Views
  • 3 replies
  • 0 Helpful votes

Resolved! Line Card for Server Farm Connectivity

For Cisco Catalyst 6807-XL, what will be the appropriate Line Card Module to connect Server Farm either 1 or 10Gb.  I am already using Line Card Module C6800-32P10G for 10Gb uplink/Downlink to IDF switches.  Can this module be used for Servers as wel...

abbasali5 by • Level 3
  • 960 Views
  • 4 replies
  • 0 Helpful votes

UCS upgrade infrastructure

In UCS we need to upgrade one-by-one as below or can we upgrade all to gather in one time ? kindly suggest. 1)Infrasturcture2) UCS3) Install Server Firmware If the FI is in cluster mode, second FI-B will get automatically sync FI-A automatically ? Af...

DNS Changes on UCSM

Guys,I am about to change my DNS IP on UCSM. I have 4 blades all hosting ESXi on it.- DNS changes are done on all 4  ESXi host with the new DNS IP.- Right now I need to make changes on the DNS IP on UCSM. Making changes to the DNS IP on UCSM will onl...

Resolved! Core Stack Mistake == Looking for advice

Here is the overview. Two years ago went from 3com 5500 to cisco. Nice Move . environment is 50 - 60 servers ESXi running about 35 servers.  First wave was to replace the core stack, Which were 3 3com 5500G , This was okay until we starting adding mo...

jdamon113 by • Community Member
  • 2469 Views
  • 7 replies
  • 0 Helpful votes

Resolved! VPC Object Tracking

Hi We have a DC setup with 7k 5k.N7k1 - N7k2 with vpc (7010 model )N7K1 is primary.peerlink from Module 7 & 8KAL is from 4We enabled Peerswitch,Peer-Gateway,Auto recovery.We didn't enable Object tracking. Could you take this design and pls suggest me...

arjunselvi by • Community Member
  • 1614 Views
  • 4 replies
  • 0 Helpful votes
Load more
Top Solution Authors
View All

Review Cisco Networking for a $25 gift card