Update: This portion of the project has finished earlier than initial projections. We are approaching our latest step in relabelling posts across the Small Business board. 1 week from today, read-only mode will be active on this discussion board fro...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Hello All, I have created 3 vlans and I have assigned it to the interface in Cisco SG300. The internet is working if manual ip is assigned and not via DHCP. I have configured the ip pool but DHCP is not getting released. If there is a proper set ...
I have done some searching, but have been unable to find the right situation that matches what I am trying to do. I'm new to VLAN/Switch Routing, so forgive maybe some newbie type questions. I have 2 discreet LANS in my network. 192.168.0.* and 19...
I have a situation where we put in a new Fortigate FW that has a DMZ interface connected to an SG100-16. Connected to the SG100 are two windows network load balanced web servers. We were experience intermittent drops in connectivity from these two se...
Resolved! Small Business switches
Hello, I have a couple of question about the SG300, I know it has ip routing enabled by default, My question is which are the considerations to create intervlan routing through router-on-a-stick scheme. I think it is a little bit different like th...
Can i install a SF300-24PP-K9-EU switch in a network with NAC?
Resolved! SG500 Stacking
I am about to stack a SG500-28 switch to an existing SG500-28. Both are in native stack mode. Will it reboot the exisiting SG500-28 that is in production? Do I need to plan for downtime for this?
Hi Everyone, We have sg-500 switches, the issue is when we reload the switch ''switchport trunk native vlan #'' command is removed under the interface. However we have saved the configurations and also upgrade the ios version as well but no luck. C...
I need to find a way to disable this permanently: Syslog Notification (Information): %AAA-I-CONNECT: New http connection for user cisco, source 192.168.1.176 destination 192.168.1.154 ACCEPTED Every time I log into an SG350 swtich I'm harassed...
Resolved! Stack Between SG550xg et SG500
Hi all, Is it possible to stack an SG500 with an SG550xg please?Regards
Resolved! SG300-10P Guest Network Setup Help
Hello Cisco community! First time post, I'm sure someone can help me with this problem of configuring something that should be simple but has eluded a solution for a week now. I've attached a very rough diagram of my topology and hopefully enough inf...
Model: SG200-08Config:Port 1 - 5 VLAN 1 UnTagged Member, VPID 1 (defult config)Port 6 - VLAN 99 Tagged Member, VLAN 1 Untagged Member, VPID 1 (default)Port 7 - VLAN 99 UnTagged Member, VPID 99Port 8 - VLAN 99 UnTagged Member, VPID 99Port 8 Tx & RX Mi...
Resolved! Does The SG300-10 Support RIP?
Hi!In the CLI documentation for the SG 300 Series, it shows sh ip route rip as a command. I have installed the latest firmware and that command is no longer available. Does the SG300 series support RIP?Thanks!Richard S.
About a year ago we installed a Shoretel VOIP Phone System and needed new switches. Old ones were 10/100 and non-POE. I purchased several SG500-52Ps. They've been great except for one problem. When powered on after an extended power outage or shutdow...
Resolved! SG300-10 L3 InterVLAN Routing
I purchased an SG300-10 with hopes of breaking my network out into 3 VLANs that can intercommunicate for LAN traffic and send internet traffic out through my NETGEAR Nighthawk X6 R8000. My first attempt was as follows: Put the switch in L3 mode.Build...
Hi, We have Cisco SG500X-48 and SG550XG-24F, and we're using the the 10Gb SR modules. When we light the fiber with these modules, we get the error on the SG500X-48. I actually have a set of SG550XG's (550XG-8F8T) that light up fine between the two w...
