Switches - Small Business

Hi everyone, Im new to this support comm. but was hoping to get some assistance with a problem Im having with the switch mentioned above. The problem is that when I plug out my IP phone the vlan gets reset to the default VLAN of the switch which is ...

Hi All Good Evening I have a query with regards to Dynamic link aggregation (802.3ad). I have a server that has two NIC ports and it is connecting to 2 different switches on port 9. these switchports are configured as access ports in VLAN 41. I need...

I have a customer that needs to know whether Cisco SF300 Switches supports to Radius COA?. If yes can i integrate Cisco SF 300 Switches with Cisco ISE 2.1 for authentication/authorization ,posture assessment & remediation. Any help would be appreciat...

Hello, I'm looking to connect a switch to my home ASUS router and I know the router doesn't support direct VLAN tagging. So my solution is to buy a SG300 and do the L3 routing and VLAN tagging directly on that instead.  My questions are the following...

Hello everyone, recently i open two RMA procedures for two old Cisco switches and i receive as replacement n°1 SG500-52P and n°1 SG500-28P, both without Rack Mount Kit (normally included with a new switch). Unfortunately the rack mount kit of the two...

I have a SG300-52 switch.  The system light flashes green continuously.  I have reset it to factory defaults and upgraded to the most recent firmware. The switch appears to be working but I am afraid to put it in production.  The documentation indica...

hi everyone ,, i just have bought a Cisco SG300-52P for my organization, i have 12 access point of ( Unifi UAP lr ) separated between two floor , i want to power those access point by my Cisco Router by POE , but it seen not working what every i trie...

Hi, firstly, I apologise, I'm no Cisco expert, just after a bit of knowledge/advice. I am using a pair of SG300-10MPP to trunk data from one place to another with a selection of VLANs. Everything is working seemingly fine, except I have one problehm...

We have a brand new SG300-10PP We have a total of 8 PoE devices that need to connect to the SG300-10pp Each devices consumes ~ 6-7 watts/each We connected 7 devices and the PoE works and devices work fine We then connected the #8 device, but it will ...

I'm trying to configure RADIUS login with my SG350-10 switch. I am able to configure RADIUS for accessing the HTTP web front end, but I cannot get it to work for all services (HTTPS, SSH, etc). Because it works for access via the HTTP service, I'm s...

Hi all Hope i am posting in the right spot as im new here :-). Im hoping you can help me with some information and ideas about a few ideas i have for our home network. Firstly i have just bought a second hand Cisco SRW2024P which is working well. We...

Yes, I am lost. Be it because so much has changed, or my own lack of education. I am starting to configure a Cisco 300-10PP managed switch. It is connected to the Internet. And the LAN. I was attempting to configure the "time" settings. It seemed tha...

Hello Cisco land. My problem, we are about to shut down an old dns server, address 208.xxx.xxx.xxx, but it looks like 600 people are still using it! What is the best command to use so when people try using the old dns (208.xxx.xxx.xxx) they get a res...

Hello, I changed my default vlan from 1 to 3 on my sg300 and now I can no longer access the web UI. I'm sure this is because I didn't properly set it up before making the change. I am in the CLI but I cannot figure out how to simply revert back so I ...

Have a switch that is out of warranty and after a reboot goes to start loaded SW and get Check Sum error! on both SW images. Then is says Both images are not valid ... Please download a new image Downloading code using XMODEM I tried loaded current F...