Switches - Small Business

Dear Cisco,we are interested in buying 300+ of these devices, iff it doessupport dot1x authorization, that means it sets the vlanaccording to the radius reply. The predecessor (SLM2008) didnot implement this feature or it was just disabled like snmp?...

Hi,Good day! Just need an assistance with regards to Cluster IP.We have two Web Servers and configured as Network Load Balancing in a cluster for failover.WEB1 IP: 192.168.1.50WEB2 IP: 192.168.1.51Both configured with Cluster IP: 192.168.1.100 on Mul...

We have 10 servers  sitting in a colo, connected to a Cisco SG300-28 Small Business 300  Series 28-port Gigabit Managed Switch.  All of which is sitting behind a  Sonicwall TZ 210 firewall.3 of the servers are used for  development and the rest are o...

I have a SG-300-52 port switch configured Layer 3 with mutiple VLANs. I have run out of ports. What is the best way (or easiest) to bring up a second SG-300-52 port switch with the same VLAN configuration?

Right now we have around 50 users in our workplace, here is a mess right now, I dont even know how it still in working condition. For 50 users we are using 5 switches and I have no idea why, I just came to this place and I want to re-organize whole n...

I'm hoping I can explain this coherently.  I have Polycom IP phones connected to a SGE2010P.  The SGE2010P in turn connects to a Cisco 3650G.  The IP PBX in turn connects to the Cisco 3650G.This we will call Exhibit APhones -> SGE2010P -> Cisco 3650G...

Is it possible to police traffic to 0bit/s?Is it possible to attach a service policy to a vlan interface?

I have an SG 200-08P. I need to restrict access to the web interface for security. Unfortunately I have found this nearly impossible. - Is there any way to restrict access to HTTPS? Seems simple but I haven't found a method of doing so. IIRC this is ...

Hi All,I have setup a new SFE2000 switch to work in Layer 3 mode using the IP address 192.168.100.254 on VLAN 1Additional VLAN's are:VLAN2     192.168.102.x     To be used for guest wireless accessVLAN3     192.168.103.xVLAN4     192.168.104.xI would...

i can't find languages file for series 200 switch...where are????

Hi allWe've have a 2 SGE2010-48 port, stacked.4 LAGS are denifed, two on primary, whitch are working, two on slave unit are NOT working.Devices connected to LAGS are de the same and same configuration (Cisco ASA 5510).Any way to fix this?

DHCP I have a cisco 2921 router connected to a cisco sg300-52 L3  switch. The switch is configured with several subnets and I need to use  the router for DHCP. I setup DHCP on the router to assign addresses to a  subnet on the switch but cannot get i...

Hello all,I have a very strange situation regarding 2 SRW248G4 switches (1.2.2a firmware).Trying to collect statistics for these switches, I noticed that ifHCOutCounters increases than decreases (!!!), querying about at 5-10 seconds interval. For exa...

I am running a small home network and purchased an SD2005 switch so I could run gigabit and get top speed from my attached NAS server.Recently I have noticed a problem with the SD2005.  Occasionally (about once a day), it will just start rapidly beep...

hello everyone,    I have SGE2010 switches and I want to implement Multiple VLAN's. Im a newbie and starting to study VLANS'sI want to implement 5 VLAN's on my test lab network and here as follows:192.168.1.x default192.168.2.x192.168.3.x192.168.20.x...