We recently announced the release of our self-serve virtual assistant. You can read the full announcement here. Videos and documents are available within a click for our latest products. Once you've told the bot what device you're using, the context ...
Forum Posts
(Updated September 2023 - Added Catalyst 1200 and Catalyst 1300 ) Hello! This sticky-post will serve as a sign-post for incoming community members. Below you will find links to pages that you may find helpful. Catalyst 1200 & 1300 Hardware Install...
Resolved! sg200 web manegment under dhcp mode
Can i configure my WAPs and switch under dhcp ISP. Or i must always disconnect ISP and connect my PC/laptop with static config LAN (192.168.1.100...) and than i can access WAP,swich web config page
I have a project where a nurse call system in a UK hospital will be connected to 24 port SF250 switches. Due to the size of the project i will potentially be using up to 90 of these switches split into multiple VLANs with RSTP enabled. does anyone fo...
Hi,I own a SG350X-48P. Today we had a massive thunderstorm coming through and one lightning strike must have hit my house or at least very close by. Lightning and thunder was without any delay and extremely loud. Right after the strike all my securit...
I hope this is a general question and its hard to word the question to search online. Here is my console port config:line con 0session-timeout 30logging synchronouslogin authentication CONSOLEstopbits 1 I am currently unable to console into this swit...
Resolved! SMB switches & Vlan ACL/Vlan Access Map
Hi Community, I didn't find anything about it, so I would like to know if SMB switches supports Vlan ACL/Vlan Access Map.Thank you
I'm a newbie this is my 1 post, sorry if I'm posting in the wrong place. I would like to update Firmware Model Name SRW2024, Hardware Version 00.03.00, Boot Version 1.0.1, Firmware Version 1.2.2b, but I can't find the latest Firmware, would someone b...
Hello, I am using the cisco SG350-10 in DHCP server mode with an IP camera and it sometimes work and sometimes not. When I connect the ethernet cable on ports 1, 8 and sometimes 6 I get the ACT LED blinking and I can connect the camera. If I try to c...
Hi All Network Topology Internet > RV325 > SG200-18 4 VLANs setup4 WAP371 APs All devices connected via the SG200-18 switchAll Network devices running ALL the Vlans. RV325 - Routing on Stick setup - no inter-vlan routing.SG200-18 = RSTP Root BrigdeI...
Hello!I'm sorry for my bad english, but I need your help...One of the switches in the company where I work is broken down. As soon as I turn on it, its indicator named "system" is blinking non stop... And every 42 seconds all its indicators(24LAN and...
Hi! I've recently upgraded the firmware, from 1.0.1 (factory firmware) to 2.0.0.10.When I open the Port Configuration section or any other that shows port list I get this:And I get half of the port's list.Any ideas?Thanks!PD: The web UI only works on...
I have missed the 6 year window :-) to update latest firmware(2.0.0.10) for my switch SLM224G. It is no longer avilable on Cisco website. Does anyone know where I can obtain it ? I have run into nasty browser issue(no modern browser works with the ...
Hi All,I have a problem similar to https://supportforums.cisco.com/message/3103915:We use passwords with special chars, worked fine with fw 1.0.1.I want to re-commission the switch, so before that, I upgraded to the latest firmware, 2.0.0.10. Since t...
Hi Everyone,I have a SG350-28P switch acting all haywire. The switch has 1 wireless link and 6 IP Cameras (PoE) connected to it. The ports where the IP cameras are connected; are dropping randomly (frequently). Port1 (where the wireless link is conn...
We are experiencing some unusual LED indication in the front panel of one access switch. All the LED are in orange color and blinking in the top left corner of the switch. Even switch is working properly and we can access the switch. But why LED is ...
Hi All, I've just bought a used Cisco Small Business SG 300-10MP switch but currently have problems setting it up. I've already factory resetted the Switch multiple times but no default password is working.. Currently tried: cisco/cisco; Cisco/Cisco...
