I recently replaced the core switch at one of my sites that consisted of two separate C9300-48Ts and three other off brand switches and installed a new stack with a C9300X-48HX, C9300-24S and a C9300-48T (running 17.12.5). This is a layer 2 network c...
Forum Posts
i am learning CiscoU, but today i am login to my account, CiscoU require to install Cisco Secure Endpoint. How can i download it, is it free or pay ?
Bonjour, Je ne trouve rien qui précise si le Fast REP est supporté sur les switches stackés de la gamme IE Cisco. Si quelqu'un sait ? Merci d'avance ! Edit : Pour être plus précis, je demande si le temps de convergence du Fast REP reste le même si u...
Hello, I'm just looking to make sure that I'm interpreting that a cable run is bad for a new install before ripping it out & starting over. Trying to hook up a new security camera that will be using 15.4w. These are the following results, please corr...
Hello,I'm planning a network setup as shown in the diagram, where SW1-SW2 and SW3-SW4 are configured using Stackwise.In this setup, I intend to connect SW1 to SW3 and SW2 to SW4, and configure MEC (Multichassis EtherChannel) accordingly.I'd like to a...
Resolved! CISCO 9200 "No space left on device"
Hello,I am trying to update a cisco 9200 switch ( in fact, it's a stack, there a 2 switchs).Switch Ports Model SW Version SW Image Mode------ ----- ----- ---------- ---------- ----* 1 32 C9200-24P 17.06.05 CAT9K_LITE_IOSXE INSTALL2 32 C9200-24P 17.06...
HiI have a couple of cisco Nexus9000 C92160YC-X as core switches. I have 6 pairs of catalyst 9300 switches connected via VPC to these cores. I was configuring auto qos voip trust on these access switches but I came across an issue on the core switche...
Any know how many times w/in a time frame a mac address needs to show up on two ports before a mac-flap error is logged? And is there a way to tune that threshold?We're running some ap's in flex mode, and a few handheld clients are roaming between a...
Resolved! err-disable state SW down interface
HelloHello I am attemping to install two cisco 9200 Series . The por 24 is in trunk mode is conecting against other 9200 series ( i dont have acces now to this SW this SW has a some SWitches on different port the SWitches are no cisco) .there is not...
Resolved! vPC from FEX interfaces
I am trying to create a vPC port-channel for two different FEX interfaces. We have two Nexus 5000 series switches connected via vPC and FEX 106 and 107 each with a connection to our Nexus 5000 switches (proda1 and proda2) connected via port-channel a...
Resolved! Packet Tracer Login Issue in Mac
I am using Cisco Packet Tracer in Mac and when I tried to login it's keep loading for a long time and no result, I am having this issue since last 2 days. However, if I tried to login netacad.com directly using browser it's working fine but the Packe...
Resolved! C1000-48P-4G ez1k error messages
Good Morning, We've got a C1000 that behaves kinda strangely and i'd like to know if its a hardware problem or a "solvable" Software Problem.Here's a Screenshot of the Console Output:ConsoleThe Switch still kinda works normally, i can configure the s...
I'm a new user of Cisco products in a public transportation agency and I'm working with both the Cisco 819 and 829 routers. These devices are installed on a large fleet of vehicles.We have written procedures for setting up both models, but the engine...
Resolved! CISCO2901/K9 %PLATFORM-3-PIP_ERR
Good day All,I have an old 2901 SW and I noticed scrolling in the logs:*Jul 16 14:19:10.135: %PLATFORM-3-PIP_ERR: PIP error reg 0x00000080*Jul 16 14:19:15.247: %PLATFORM-3-PIP_ERR: PIP error reg 0x00000080*Jul 16 14:19:20.463: %PLATFORM-3-PIP_ERR: PI...
Hi All, I have the following setup in CML: SW1 is the Root BirdgeI have VLANs 1-20All Switches have the same MST configuration and running in the same region. When I shut down interface gi1/0/3 on SW3 the MST environment converges and uses Gi1/0/6 a...
