Hello, Cisco Community!I’m really happy to share that I’ll be hosting the Cisco Community Lab Series, a brand-new hands-on learning journey designed to help you build practical networking skills step by step.Every Thursday at 8 PM EST, I’ll post a ne...
Forum Posts
I am trying to setup an IP HELPER-ADDRESS per SVI but clients are not getting IP address from the assigned DHCP Server in the IP HELPER Address. C1300-24XT has also different syntax or argument in declaring IP HELPER-ADDRESS.Catalyst 1300 Series Man...
Do you still run VTP Version 2?Then watch out for this bug:https://bst.cloudapps.cisco.com/bugsearch/bug/CSCwi46941For me this bug is like a time bomb.Two of our customers ran into it after upgrading from an affected release to a non-affected release...
I have a customer who is struggling with the Thumbscrews that are used to secure these cables to the routers. I am trying to find out if there is a part number associated with them and if it is possible to purchase replacement screws. Or if the...
Hello Everyone,We are looking into creating an automated report with all the ports that show status down on a Cisco switch and the time stamp when was the port last active. We were thinking to use Ansible to extract the output from the "show interfac...
Resolved! Best QOS for monitoring throughput
So what does anyone suggest the best QOS policy to implement on a a switch interface (switchport, SVI, even Tunnel, etc.) to capture and/or monitor throughput?
I am looking for AKIPS monitoring tool for cisco devices. Given the requirements below I am concerned as to the load AKIPS may place on network devices. Any idea on the load imposed by AKIPS ? Any Way to do impact assessment ? Any document ? 5000+...
Resolved! SG300-28P firmware update
Hi all,I have in my hand an sg300-28p with firmware 1.3.0.62 and bootloader 1.1.0.6. I want to put it in the latest version (I'm aware of the in-between I have to do because of new bootloader version) but I don't see any firmware for my switch.There ...
I have a 9200L as a core switch, with 5 other switches attached by 10GigEthernet cables. I cannot seem to get to the internet for all but the primary VLan on any of the other 9200L switches. Please help.
Hi there,Thanks for reading!I'm seeing an oddity when trying to join a laptop to an SSID in PT. The problem is in the UI where I set configuration for Wireless0 nic. When I select an authentication type, the cursor jumps to the WEP password field a...
I'm replacing a failed switch in an 8-switch Catalyst 9300X stack, which includes:1x C9300X-48HX-E7x C9300X-48TX-E (including the failed unit)The replacement switch is a C9300X-48TX-E. I followed the standard procedure:Powered off the replacement swi...
Resolved! Catalyst C3560-24PS-S - Upgrade path
Hello,I'm looking for some direction on upgrading this platform, it is currently on IOS 12.2(35) SE5.Curious if this requires multiple upgrades and what version I should upgrade to? (I'm assuming 15.X) Thank you.
After Factory reset I install system from TFTP server.Now switch stuck in rommon after reebotPlatform C9300LPLATFORM_TYPE C9300L speed 9600Booting Recovery Image 16.12.1 Initiating Emergency Installation of bundle tftp:///cat9k_iosxe.17.18.01.SPA.bin...
Should be a pretty simple question, but I can't seem to find an answer and I've tried all of the old tricks.What I want to know is simple, using a terminal emulator (or in my case a Cisco router as a terminal server) how can I issue a 'break' to inte...
I am planning to replace a Cisco 3750E-24TD with Cisco 2960G-24TC.I wanted to make sure that 2960 will handle the load. When I went through the datasheets, I got the below queries. What is the difference between Forwarding Bandwidth & Forwarding rate...
I have a 9200L-48P-4X switch stacked with a 9200L-48P-10G. When attempting to update to version 17.09.05, I encounter a "low disk" error on the 1G switch, while the 10G switch does not have this issue. The update image copies to the switch, but when ...
