Can anyone confirm if GLC-TE is supported on C9500-48YAC switch? I got this from TMG Matrix and it shows supported but would like to confirm if anyone is using in their environment. TIA Hitesh
Forum Posts
Hi, I need to configure a Nexus 9000 switch ( N9K-C9348GC-FXP - release 7.0(3)I7(3) ) to authenticate one or more users using TACACS and another user using Local authentication simultaneously. I tried to configure "aaa authentication login default ...
Hi All!Does WS-X6548-GE-45AF and WS-X6148A-GE-45AF support NAT?
can not ip access-group name in for Catalyst 2960-S Series SwitchesCatalyst 2960S-24TS-S Switch it always return port based .... can not use in this image
Hi, The switch Cisco 2960CX-8PC-L supports PoE+, the total power budget is 124W, which means maximum 4 ports can support PoE+. Let's say the switch now has 2 PoE+ devices connected, does it mean the switch's PoE budget become 64W? Can we use the 64W...
Hi everyone, we will be replacing our current core (4900M) and layer 2 switches (3750X) with C9500-24Y4C with advantage license and same for the L2 switches with another pair of C9500-24Y4C with essentials license. Currently we are doing HSRP on the ...
Hi all, I have a Nexus 9k switch running the latest 9.3.3 NX-OS software. It's querying a modern Cisco router which is acting as an NTP server. This NTP server communicates with dozens of various other devices at either NTP v3 or v4 depending on thei...
Hi, I am new here so please forgive me if there are some dumb questions... Basically I have 2 x 9300 switches that are running PIM-SM on them that are connected to each other over a port channel. I have started my config below (excluding the physica...
Hello Guys, There’s anything special I need to do to get a bare-metal to pxe boot on a trunk port? I can’t get any machine to pxe boot, would appreciate your help if someone paste there configuration, although all server running flat vlan pxe boot f...
In regards to using an ACL under the "user", is the ACL where you enter the IP of the receiver/Solarwinds, PRTG, etc?Under the "group" config, for what circumstances do you just want read access or only write access, or both?Communities are no longer...
Hi team , Please i need your help with this issue: I have 4500 x in vss . All phisical links and all logical port-channels are the same i mean all enable jumbo frames : interface TenGigabitEthernet1/1/6 switchport access vlan 712 switchport mode ac...
Hi,I was trying to update IOS on Cisco 3650 Switch .But it gone in rommon mode but when in rommon mode (Switch: ) i was trying to emergency-install usbflash0:/<ios.bin>But it occurred an error like "booting... interface ge 0 link down***error phy li...
In VMware world, there is a parameter on ESXi host, called MaxConnectPerIP, define how many NFS mounts can use over an IP. If the number exceeds the value, additional mounts will be starting to share the TCP connections. My questions is, will many NF...
Looking for help to bond 2 NICs on a Barracuda Backup appliance. The 2nd NIC on the appliance has been activated by Barracuda support. If NIC 2 (connected to gi1/0/8) is active, I can not ping the device. If I shutdown port gi1/0/8, I can ping the...
Hi, After I was configuring cisco sg220-50P, I could not access the switch through browser by its management IP nor is ping reaching through cmd. How to enable HTTP to access the GUI browser? #sh line listLine Type | AAA Type | List Name----------...
