I am very rusty on QOS in general and 6500 QOS in particular so would appreciate it if someone could give a definitive answer on the following. Pair of 6500s running 12.2(33)SXI with multiple SVIs, using vlan based QOS and applying service policie...
Forum Posts
Hello Everyone, We want to have multiple SSIDs for different sections of the company, each on their own VLAN. So far, I have each of these up and running. However, on one half of the building, users can't get a DHCP address from the main switch whe...
Resolved! ACL on Cisco Switch to isolate machines
I am trying to isolate a host on our network to only see the server, and isolate it from everything else on the network. PCA is 10.10.10.2 Server is 10.10.10.5 I need the server to communicate with PCA and all other devices, but need PCA to only ...
Hello,We have already a L3 port channel configured and running between two pair VSS of 6880X and 6500 with two interfaces and would like to add two more interfaces, I plan to do it like below:Configure both new interfaces as the interfaces already co...
Resolved! Lost access to CUCM web admin page 7.x
Hi Cisco techs,I have lost access to my CUCM web admin page version 7.xThe only thing that has changed is the default router via ISP for NBN purpose.. Meaning that previous router ip was 192.168.0.1 to 192.168.20.1I access this via Firefox https://19...
Hi All,I have below error on Cisco 6807 VSS.469489: Mar 22 13:57:52.687: %EARL-SW2_DFC1-1-EXCESSIVE_PARITY_ERROR: EARL 0: Parity error detected in VRAM469490: Mar22 13:57:55.975: %EARL-SW2_DFC1-1-EXCESSIVE_PARITY_ERROR: EARL 0: Parity error detected ...
when i rty to configure ospf on cisco switch 3850 "protocol not in this image"What would be ths solution
Resolved! Cisco 841M-4X
Hi, Need to know what will be the forwarding capacity in Kpps of Cisco841M-4X router at 64 bytes. Also if any public document available, pls share the link Thanks Navneet
I have a 3750G acting as a core Layer 3 switch with two 4506 switches down stream directly from it, Switch 01 on Port channel 1, and Switch 02 on Port channel 2. ARP inspection is turned on for all VLANs and we have DHCP Snooping enabled as well I ha...
In my network, I have two switch- one is 2960 and another is 3650! 2690 48TS-LL for access from different floor and 3650 24TS-L for the core network. I have several vlan's configured in core switch and configure port's as trunk for the access switch ...
Resolved! Round-robin forward to 2 hosts
Hi everyone, Currently I'm having one ASA 5516 with behind it two loadbalancers/proxys and two FTP servers.See below.I'm trying to figure out how to send incoming ftp connections to the two proxy servers, but my current configuration doesnt seem to w...
Hi AllWe seem to be getting a high number of logs on our core switch, a 6509, they recently only just started showing. %MCAST-SW1_SP-6-ETRACK_STATS_LIMIT_EXCEEDED: Number of entries in IGMP snooping explicit-tracking statistics has exceeded the perma...
Hi All, I see high ping response in reaching my Cisco 2950 switches in my LAN , and all other model swicthes are less than 1ms.
Hi all; I'm new in multicast and I'm asked in my company to activate IGMPv3 in my 2960 switch;we have a server witch can send only in IGMPv3, this server don't work with IGMPv2 so what I did is using an HP switch (1920) I tried activating IGMPv2 the ...
Hi guys, We have issue with the Core Switch C4506 utilization. It had increased recently and going till 75%. Based on the below commands, I see the following outputs. I have tried to unmanage device using SNMP and checked, still no help. I know the ...
