Is it possible to disable entering an enable mode on IOS ?Im deploying radius servers with two user groups (lvl 1 and lvl 15) my goal is to do that users who are lvl 1 would be not permited to enter enable mode.Yes, i know i can create a password for...
HI I have this digaram where i want OOB managment to be configured. means if some user wants to come from outside via FW and access my CORE switch.Internet--->FW-->3750 mgmt switch--->core switch--->access layer. for this purpose I want to create a L...
HiI am new in network management, I read about SNMP protocol, but I need to understand one point.We have a Server and a Switch with their SNMP Agents,The Server connectes to the Switch, Is it possible for The SNMP Agent in that Switch directly access...
Hello, Wondering if you can help me. I have a Cisco WS-C2960S-48FPS-L switch which connects some VOIP conference phones (Polycom SoundStation IP7000 or IP6000). The phones don't come up. It looks like the switch is not providing enough power. If I co...
A very quick question, does the C3850-NM-4-10G support both SFP and SFP+ transceivers? I'm about 99% sure that it does. Just wanted to be 100% sure. Datasheet seems to suggest it does although in my eyes is not 100% clear. Thanks in advance to anyon...
Hi all, Can some one help me out and expalain this calculation with wrong metric output? is it a bug?Show eigrp topology 6.0.0.0/8 with following BW and Delay for EIGRP metric calculationMinimun bandwidth = 30000 KbitTotal Delay = 1130 microseconds C...
hello,my question is how do i know the cable that connected to the device interface using cisco commands.which it could be used to figure out if the user does use wrong cable to connect two devices. thanks.
Hi to alli have a problem in my cisco router 2911 ios ver.15 its make reload every 3 hours and when i showing version the result is :Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.2(3)T1, RELEASE SOFTWARE (fc1)Technical Support:...
Hi All, We have cisco stack switch of 3750 with 5 units it as below. Switch Ports Model SW Version SW Image------ ----- ----- ---------- ---------- 1 52 WS-C3750-48P 12.2(55)SE4 C...
How can i create a 6 DHCP scope on cisco SG300-10POE Series switches??There is any different commands Depent Upon each CiSCO switch models????
Hello Team, I need help to upgrade IOS of 6500 Series which has QUAD SUP 2T into it.Could you please send me procedure to upgrade it? Regards,Gaurish S
What are the options available to reconfigure cisco 6807 switch? and which is best optionBG:- The existing 6807 switch is used for one location and its is getting re-used for other building with new set of configuration. Please anyone suggest with co...
ModelDescriptionTotal QSFP or SFP+ PortsC9500-12QCisco Catalyst 9500 Series 12-port 40 Gigabit Ethernet with QSFP12 QSFP/12 SFP+C9500-24QCisco Catalyst 9500 Series 24-port 40 Gigabit Ethernet with QSFP+24 QSFP/24 SFP+C9500-40XCisco Catalyst 9500 Seri...
See attached for a diagram of the layout of the network. My problem is i require remote access to all of the equipment which i have managed to achieve apart from the L2-SW1 device. Below is what i have found out from troubleshooting; The gateways o...
Hi I have just change the MTU size on all switches in my lab to 1550(mtu, jumbo, routing) and when I do a ping sweep I get to transfer 1550B packets.But when i look at show vlan, the vlan MTU is still 1500. If I then do a show vlan mtu, the MTU is 15...
