Switching

i have a switch with a ipservices ios , the problem is i don't have credentials to download the newer ipservices ios , can i install the ipbase instead on the switch or it would cause issues? the switch is C3560-48PS

Any one help me I can not use $t when archive command   :  path tftp://10.34.120.159/$h_$t  .   result error - bad file number but i remove $t  it success. device hardware:  cisco WS-C2960-24PC-L  Software version 12.2 (44) SE6 LANBASE

I am testing redistribute static over ospf in Unetlab 1.0.6 PROBLEM:1. can't ping 8.8.8.8 from R2 and R3What I miss heretq INFO:R1router ospf 1 redistribute static subnets network 1.0.0.0 0.0.0.255 area 0 network 12.12.12.0 0.0.0.3 area 0 network 31....

Hi, I've just replcaed our Juniper SSG firewall with an ASA 5512-x.  I have a static NAT rule that is Natting the phone system through to a public IP address.  I don't have any outbound firewall rules setup as trust to untrust is allowed without the ...

Hello I have the following config  and I have to migrate this to a nexus 5000, where Im lost is with the stanby configs, how to apply this in the 5000. Any one can give some tips? thanks all. interface Vlan120 ip address 152.28.9.2 255.255.255.0 se...

This might be a very simple question, but what is the correct configuration settings when you want to create an ether-channel using 2 ports on the same Nexus switch to a Esxi host? Do you need to specify the "vpc" command within the interface port-c...

Hi,I have 2 4507R core switches, which are in a HSRP configuration. I plan to implement a 4 switch 3750G stack. My question is...what is the best method to uplink the stack to the core switches?Ideally, I would like a 2GB etherchannel to each core sw...

Hi, We are planning to use 30cms Power Stack cable between our 5 Switches with 1 RU space between the switches as well. To maintain this 1 RU space and to make use of this 30cms Power stack Cable, I have designed two Options and those file are attach...

I am going to attempt to segment a small LAN with three VLANs.  I will have one VLAN for data, another for security cameras, and a third for public Internet access.  I have a good understanding of how to do this but one thing I am not sure of.  Do I ...

Hi everyone, I have a Cisco3750G-24PS-S running in my home environment, along with other things. I was doing fine, until summer. Now, ambient temperature is getting too high, increasing the operating temperature on Cisco3750. Usually it runs around 4...

Dear Team, Hello, Qus :        1. We have one core switch i.e 3560x switch and we configured the switch with 9 Vlan for 9 divisions, each division should not talk            each other even that is also working fine. In each Vlan we enabled dhcp pool...

Hi, In 2960x switch, all the ports goes down at a time and come up after 2 sec. It is happening every 5 mins. Regards, Gopinath

Hello, when I try to trace Ip with source cellular interface form cisco router I always got asterisk as blow traceroute 10.194.52.13 source Cellular0Type escape sequence to abort.Tracing the route to 10.194.52.13  1  *  *  *   2  *  *  *   3  *  *  *...

Hello Experts, We have one static nat issue, i just wanted to discuss with you guys if some one had same issues like me  we have one router which is connected to LL and we are running DMVPN over that, inside interface of the router connected to fir...